Storage Guidelines; Product Description; Pump Design; Pump Description - Lowara ESHE Manual De Instalación, Funcionamiento Y Mantenimiento

out motor must be fixed and transported as shown in
Figure 6 (page 324).
In this last case remove coupling guards from drive
lantern and cross the lifting ropes/bands.

2.3 Storage guidelines

Storage location
The product must be stored in a covered and dry lo-
cation free from heat, dirt, and vibrations.
NOTICE:
Protect the product against humidity, heat sources,
and mechanical damage.
NOTICE:
Do not place heavy weights on the packed product.
2.3.1 Long-term storage
If the unit is stored for more than 6 months, these re-
quirements apply:
• Store in a covered and dry location.
• Store the unit free from heat, dirt, and vibrations.
• Rotate the shaft by hand several times at least
every three months.
For questions about possible long-term storage
treatment services, please contact your local sales
and service representative.
Ambient temperature
The product must be stored at an ambient tempera-
ture from -5°C to +40°C (23°F to 104°F).

3 Product Description

3.1 Pump design

The pump is a horizontal pump with volute casing
close coupled to standard electric motors.
The pump can be used for handling:
• Cold or warm water
• Clean liquids
• Liquids which are not chemically and mechani-
cally aggressive to the pump materials.
• Liquids which are moderately aggressive to the
pump materials.
Intended use
The pump is suitable for:
• Water supply and water treatment
• Cooling and hot water supply in industries and
building services
• Irrigation and sprinkler systems
• Heating systems
Additional uses for optional material:
• District heating
• General industry
Improper use
WARNING:
Improper use of the pump may create
dangerous conditions and cause person-
al injury and damage to property.
An improper use of the product leads to the loss of
the warranty.
Examples of improper use:
• Liquids not compatible with the pump construc-
tion materials
• Hazardous liquids (such as toxic, explosive, flam-
mable, or corrosive liquids)
• Potable liquids other than water (for example,
wine or milk)
Examples of improper installation:
• Hazardous locations (such as explosive, or cor-
rosive atmospheres).
• Location where the air temperature is very high
or there is poor ventilation.
• Outdoor installations where there is no protection
against rain or freezing temperatures.
DANGER:
Do not use this pump to handle flamma-
ble and/or explosive liquids.
NOTICE:
• Do not use this pump to handle liquids containing
abrasive, solid, or fibrous substances.
• Do not use the pump for flow rates beyond the
specified flow rates on the data plate.
Special applications
Contact the local sales and service representative in
the following cases:
• If the density and/or viscosity value of the pump-
ed liquid exceeds the value of water, such as wa-
ter with glycol; as it may require a more powerful
motor.
• If the pumped liquid is chemically treated (for ex-
ample softened, deionized, demineralized etc.).
• Any situation that is different from the ones that is
described and relate to the nature of the liquid.
3.2 Pump denomination
See Figure 2 (page 311) for an explanation of the
denomination code for the pump and one example.
3.3 Nameplate
The nameplate is located on the fan cover. The
name plate lists key product specifications. For more
information, see Figure 1
The nameplate provides information regarding the
impeller and casing material, the mechanical seal
and their materials. For more information, see
3 (page 320).
IMQ or TUV or IRAM or other marks (for electric
pump only)
Unless otherwise specified, for products with a mark
of electrical-related safety approval, the approval re-
fers exclusively to the electrical pump.

3.4 Pump description

• Connection dimensions according EN 733 (mod-
els 32-125...-200; 40-125...-250; 50-125...-250;
65-160...-250; 80-160...-250).
• Volute casing pump with back pull out power
end.
3.5 Material
The metallic parts of the pump that come in contact
with water are made of the following:
en - Original instructions
(page 307)
Figure
15