Tabla De Contenido; Table Of Specifications - Gumotex SWING 1 Manual Del Usuario

User's Manual
• A recreational vessel designed for use on internal waterways with an expected wind strength reaching
Grade 4 on the Beaufort Scale inclusive and a determining wave height of up to 0.3 metres inclusive, with
occasional waves up to 0.5 metres of height caused e.g. by vessels passing by.
• The boat has been manufactured in compliance with the EN ISO 6185-1 Standard, Category IIIB.
• Related standards: EN ISO 10087, EN ISO 10240, EN ISO 14945.
TABLE OF CONTENTS:
Dear Customer,
This manual will help you to easily and safely master your vessel.
It contains a detailed description of the vessel, the supplied or built-in
equipment, its sets as well as information about its control and mainte-
nance. Please read it carefully, thereby getting to know the boat before
actually using it.
If this is your first vessel or you have changed the type of vessel and
do not know this type well, please get acquainted with its maintenance
and control prior to your first individual use of the vessel so that it is safe
and comfortable. Your dealer or the National Yacht Federation or club
will recommend you appropriate training courses or qualified instructors.
Do not pull off until the expected sailing conditions (wind strength and
wave height) are appropriate for the construction category of your vessel
and you and your crew are able to control it in these conditions.
Please store this manual in a safe place and hand it over to the new
owner should you sell the vessel.

1. Table of specifications

(Dimensions when inflated)
Length (cm)
Width (cm)
Diameter of sidewall cylinders (cm)
Number of air chambers
Dimensions of the folded product (cm)
Dimensions - packed in cardboard (cm)
Maximum operational pressure
Weight (kg)
Maximum load (kg)
Maximum number of kayakers
Draught (cm)
Highest anchor above surface (cm)
2. Technical description - see Fig. 1
1. side tube
2. bottom
3. PUSH/PUSH valve - it allows inflating/deflating, regulati-
on and measurement of pressure with a pressure gauge
(placed below the top part of the boat)
4. pressure-relief valve (placed below the top part of the boat)
5. front seat with a back-rest
6. rear seat with a back-rest
7. foot-rest (placed below the top of the boat)
8. plastic handle
9. manufacturer's label
10. yellow „WARNING" label (sewn into the edge of the kayak)
12. bungee netting
13. black zip with slider
8
SWING 1, SWING 2
KAYAK
1. Table of Specifications
2. Technical Description
3. Inflation Instructions
4. Riding the boat
5. Folding of the boat
6. Treatment and Storage
7. Guarantee Conditions
8. Boat Repairing
9. Product Disposal Method
10. Packaging Disposal Method
11. Type Parameters Tag
12. Safety Caution
SWING 1
316
87
20,3
3
69 x 38 x 23
75 x 43 x 29,5
0,02MPa [0,2Bar / 3PSI]
11,2
120
1
15
40
14. anchoring for foot-rest attachment (detail A)
15. anchoring of the rest on the tube (detail B)
16. attachment of the rest to the kayak reinforcement (detail B)
17. seat attachment
18. reinforcement attachment (placed below the top part
of the boat - Fig. 2)
19. tracking fin attachment
20. kayak reinforcement
ACCESSORY SUPPLIED WITH THE KAYAK:
Single-seat version - reinforcements Nos. 1 and 2. Two-seat
version - reinforcements Nos. 3, 4, 5. Belt for strapping the
folded kayak, user's manual with the warranty certificate,
sponge in a netting bag, repair kit containing glue, patches
and valve adaptors.
VERSION 6/2016
GB
page
SWING 2
402
87
20,3
3
69 x 39 x 24
76 x 50 x 34
0,02MPa [0,2Bar / 3PSI]
14,1
220
2
15
40
8
8
9
9
9
10
10
10
10
10
10
11