Bestway STEEL PRO 56045 Manual Del Usuario página 4

Rescue equipment should include but not limited to items such as coastguard approved ring buoy with attached
rope and strong, rigid Rescue Pole of at least 366cm (12').
Post emergency numbers including:
• Fire (France 18)
• Police
• Ambulance (France 15)
• Poison Control Hotline
• Full home address
Keep a cordless water-resistant phone nearby pool during use.
In case of an accident:
• Take all the children out of the water immediately.
• Call for emergency support and follow their instruction/advice.
• Replace wet clothing with dry clothing.
Watch and react! When supervising children stay close at hand and always be alert.
Teach your children to swim as soon as possible.
All filtering systems are compliant with installation standard NF C 15-100 stating that any electrical appliance
located less than 3.5 meters from the pool and freely accessible must only have a 12V supply. Any electrical
appliance with a 220V mains supply must be located at least 3.5 meters from the edge of the pool. Always ask
the manufacturer for advice before making any change to one or more components of the filtering system.(For
France only)
PLEASE READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE.
Preparation
NOTE: The pool must be set up on a completely flat and level surface. Please do not install the pool if the
surface is inclined or slope.
• Check with your local city council for by-laws relating to fencing, barriers, lighting and safety requirements and
ensure you comply with all laws.
• Take the pool and accessories out of the carton with care. If the pool set comes with a ladder, the ladder
requires a crosshead screwdriver or an adjustable wrench ( not included ) to assemble.
• Locate your pool with a minimum of 122cm (4 feet) space on all sides so that a child can not use an object to
climb into the pool. Do not set up directly under overhead power lines or trees and be sure the location does not
contain underground utility pipes, lines or cables of any kind.
• It is essential the pool is set up on solid, level ground. If the pool is set up on uneven ground it can result in
collapse of the pool and flooding, causing serious personal injury and/or damage to personal property. Setting
up on uneven ground will void the warranty and service claims.
• Sand should not be used to create a level base, the ground should be dug out if necessary.
• Do not set pool up on driveways, decks, platforms, gravel or asphalt. Ground should be firm enough to
withstand the pressure of the water; mud, sand, soft / loose soil or tar are not suitable.
• The ground must be cleared of all objects and debris including stones and twigs.
NOTE: Lawn or other vegetation under the pool will die and may cause odors and slime, therefore we
recommend removing all grass from where the pool will be located. Avoid locating your pool over or beside
areas prone to aggressive plant and weed species as they may grow through the ground cloth or liner.
• We highly recommend that once the pool is unfolded on the ground cloth to let it sit exposed to direct sunlight
for 1 hour or more so that the pool is more flexible during set up.
• If purchased with a pump, the pump should be installed after pool is fully assembled. Remember to locate the
intake and return outlets towards the outside power source.
NOTE: If you bought a filter pump, this element has a separate manual instructions. Please open its relative box
for details.
• If you bought a separate ladder for your pool, make sure it matches the pool size.
• Regularly check to make sure the ladder is properly assembled.
NOTE: The ladder is only to be used for entering and exiting the pool.
Installation
Fig. 1 Fig. 2
Fig. 5 Fig. 6
Fig. 9 Fig. 10
Assembly of the Steel Pro Frame pool can be completed without tools.
NOTE: It is important to assemble pool in the order shown below.
1. Lay out all parts and check that you have the correct quantities as listed in the parts guide. If you are missing
any part do not assemble the pool, contact our Customer Service Department for assistance.
2. If pool was purchased with a ground cloth, spread carefully at the desired location. Ensure the pool is located
within distance of a 220-240volt AC outlet protected by a RCD (Residual Current Device).
3. Spread out the pool and make sure the pool is right side up, let it sit exposed to direct sunlight for 1 hour or
more so that the pool is more flexibleduring set up.
4. Turn the pool so the drain valve is near the area where your plan to drain the water and pump valves are
facing the RCD outlet.
ATTENTION: Do not drag the pool on the ground in order to avoid puncturing from sharp objects. Bestway
Inflatables will not be responsible for damage caused to the pool due to mishandling or failure to follow these
instructions.
5. Insert the stopper plug into the inlet and outlet on the wall of the pool from the inside of the pool. (See Fig.10)
NOTE: For 549cm x 122cm (18' x 48"), 549cm x 132cm (18' x 52") pools, please refer to the connection
valve installation on following page.
6. Insert top rail (A) into the pole pockets at the top of the pool. (See Fig.1)
7. Connect top rail (A) with T-Connector (C) at each of corner and insert pins (D) into gasket (F) first and then
into pre-drilled holes of the frame.
NOTE: The gasket cups should face downwards to prevent water leaking into the top rails. (See Fig.2,3,4)
8. Repeat steps 6 and 7 until all top rails (A) are connected with T-Connectors (C) and the top frame is set up.
For ease of assembly slightly raise the last 2 rails to an inverted v shape and insert into the last
T-Connectors(C). Slowly lower until fully connected taking care not to pinch your fingers. (See Fig.5)
9. Put all vertical pool legs (B) inside the bottom rope and the pool wall band. Connect vertical pool leg (B) into
the bottom of the T-Connector (C) . Make sure the vertical pool leg (B) has the spring loaded pins at the top
when connecting the T-Connector (C). (See Fig.6)
NOTE: For 244cm x 61cm (8' x 24") pools, no bottom rope and wall band. For 305cm x 76cm (10' x 30"),
366cm x 76cm (12' x 30") pools, no bottom rope.
10. Attach all footings (E) to the bottom of the vertical pool legs (B). (See Fig.7)
11. Tighten the rope at the bottom of the pool until the legs are straight. (See Fig.8)
12. Pull the frame from different directions to ensure all rails, pool legs and connectors are firmly jointed.
(See Fig.9)
13. Ensure drain valve is firmly closed.
14. Put 1" to 2" water in the pool to cover the floor. Once pool floor is slightly covered, gently smooth out all
wrinkles. Start in the center of the pool and work your way clockwise to the outside.
Connection Valve Assembly
For 549cm x 122cm (18' x 48"), 549cm x 132cm (18' x 52") pool model
1. Screw the Debris Screen onto the Connector. (See Fig.12)
2. From inside the pool, insert this assembled Unit to the pool's inlet A and outlet B. (See Fig.13)
No Jumping
Shallow Water
No Diving
Shallow Water
Fig. 3 Fig. 4
Fig. 7 Fig. 8
NOTE: Ensure the Gasket is properly in place on the assembled Unit inside of the pool liner.
3. From outside of the pool, tighten the Connector Nut onto the assembled Unit. (See Fig. 14)
4. Hand-tighten the Control Valve to the assembled Unit. (See Fig.15)
NOTE: Check that both the Control Valve Gasket and O-ring are correctly positioned on the Control Valve.
5. Refer to the pool manual for the rest of the pool installation.
OPERATION NOTE: Use the control screw on top of the Control Valve to open and close the Valve.
(See Fig.16)
6. Make sure the valve is closed.
Fig. 11
Fig. 14
Pool Outside
Filling Pool with Water
ATTENTION: Do not leave pool unattended while filling with water
1. Fill pool to drain valve.
STOP
2. Turn water off. Check that the water is not collecting on any side to ensure the pool is level. If pool is not level,
drain water and re-level ground by digging out (See Fig. 19). Never attempt to move the pool with water in it,
serious personal injury or damage to the pool may result.
NOTE: Your pool may contain up to xxxxx liters/xxxx gallons which equals xxxxx pounds of pressure. If your
pool has any bulge or uneven side then the pool is not level, the sides may burst and the water may discharge
suddenly causing serious personal injury and/or damage to property.
3. When level, fill pool to lowest pump valve.
STOP
4. Turn water off. Check valves for secure fit.
5. Fill pool until water capacity is 90%, DO NOT OVERFILL as this could cause
the pool to collapse. In times of heavy rainfall you may need to empty some
of the water to ensure the level is correct. (See Fig. 18)
6. Check pool for any leaks at valves or seams, check ground cloth for any
evident water loss. Do not add chemicals until this has been done.
7. In the event of a leak, patch your pool using the patch kit provided. Refer to
the FAQ's for further information.
Fig. 18
Fig. 19
Flat, Level Ground - CORRECT
Proper Water Level
NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.
Pool Maintenance
If you do not adhere to the maintenance guidelines below, your health might be at risk, especially that of your
children.
NOTE: The filter pump is used to circulate the water and to filter small particles to keep your water free of
suspended dirt particles. In order to keep your pool water clean and hygienic you must add chemicals.
To keep your pool clean:
1. Contact your local pool supply shop for advice and purchase of chemicals and PH kits.One of the most
important factors to increase the life of the liner is to keep continuosly clean and healthy water. Please follow
strictly the instructions from professional technicians for the water treatment through the use of chemicals.
2. Locate a bucket of water next to pool to clean users' feet before entering pool.
3. Cover the pool when not in use.
4. Skim pool regularly to avoid settled dirt.
5. Check the filter cartridge regularly, change filter cartridge if filter cartridge remains soiled or discolored. Suggest
replacing the filter cartridge every 2 weeks.
6. Gently clean any scum from the side with a clean cloth.
7. To improve the water quality we suggest to use Bestway accessories like skimmer, maintenance kits. Please
visit our website www.bestway-service.com or contact your pool supplier. Please be careful in case of rain
water, kindly check that the water level is not higher than the expected one. If so, please act consequently.
Proper maintenance can maximize the life of your pool.
ATTENTION: Do not use pump when pool is in use.
During the season of use of the swimming pool, the filtration system must be necessarily put into service every
day, enough for a long time to assure at least a complete renewal of the volume of water.
Repair
If your pool is damaged, use the repair patch. -see FAQ's for instructions.
Dismantling
1. Unscrew the drain valve cap on the outside of the pool counter clockwise and remove.
2. Connect the adaptor to the hose and put the other end of the hose in the area where you are going to drain
your pool. (Check local regulations for drainage by-laws).
3. Screw control ring of the hose adaptor onto the drain valve clockwise. The drain valve will be open and water
will start to drain automatically.
ATTENTION: Water flow can be controlled with the control ring.
4. When draining is finished, unscrew the control ring to close the valve.
5. Disconnect the hose.
6. Screw the cap back onto the drain valve.
7. Air dry pool.
ATTENTION: Do not leave the drained pool outside.
Storage
1. Please remove all the accessories and spare parts of the pool and store them clean and dry.
2. Once pool is completely dry, sprinkle with talcum powder to prevent pool from sticking together, fold pool
carefully. If pool is not completely dry, mould may result and will damage the pool liner.
3. Store liner and accessories in a dry place with a moderate temperature between 5ºC / 41ºF and 38ºC / 100ºF.
4
Fig. 12 Fig. 13
Pool Outside
Fig. 15
Fig. 16
Pool Outside
Fig. 17
Bumpy, Sloping Ground - INCORRECT
Gasket
S-S-001480