Steamfast SF-294 Guia Del Usuario página 8

Using Your
3-in-1 Steam Mop
GENERAL STEAMING TIPS
You will find nearly limitless uses for your 3-in-1 Steam Mop. There are no rules when it comes to
steam cleaning and/or the attachments you received with your unit. Use whichever attachment
seems to accomplish the intended job quickly and easily. Below are a few starting guidelines:
•
Many surfaces only require to be sprayed with the Jet Nozzle to clean and disinfect them, then
wiped with a clean dry cloth, towel, or paper towel.
EX: kitchen counters, microwaves, stove tops, bathroom sinks, kitchen and bath fixtures
•
The soft bristle and hard nylon Utility Brushes can be used on most surfaces for hard-to-remove
dirt, grime spots or stains.
EX: baked on food on ovens and oven doors, baked on stove top spills, bath and/or
kitchen grease and grime, rubber seal on the refrigerator, under/around bath and
kitchen fixtures, bath tile seams, grouting
NOTE: Use careful judgement when deciding what surface to clean with any Utility
Brush. Some delicate surfaces may be scratched or damaged by the bristles. If you are
unsure whether or not a surface will be damaged, it is recommended that you test a
small inconspicuous spot before proceeding.
•
Steam is effective for removing spots and stains from clothing and upholstery. This can be
done with steam alone or with a stain remover designed for your specific use. DO NOT put any
type of chemical or liquid product in your steamer however; only water is to be used in the unit.
•
Older, dried stains on carpet or hard floor surfaces may require a bit of extra scrubbing with one
of the Utility Brushes and/or a product designed for stain removal. It is helpful on carpet to blot
with a clean dry towel to help remove the spot/stain.
•
The brass Utility Brush is useful for heavy-duty jobs and durable surfaces such as BBQ grills,
oven racks, etc. DO NOT use this Brush on anything that the hard bristles might scratch or
damage.
•
The Extension Pole should be attached for mopping floors, but is also useful for reaching
overhead or otherwise hard-to-reach places. When raising unit to reach high places, it is best
to grasp Pole with both hands for better support.
This should help to get you started with your new 3-in-1 Steam Mop. As you use your steamer,
you will find what works best for you and your cleaning projects. Should you have any questions
on how to best utilize you new steamer, please feel free to contact our Consumer Service
Department at:
1-800-711-6617 or consumerservice@steamfast.com
14 | ENGLISH
Storage & Care
PROPER STORAGE
Preparing your 3-in-1 Steam Mop for storage is quick and simple. When you have completed
your tasks, follow the steps listed below.
1. Set Steam Control Dial to and unplug power cord from electrical outlet.
"OFF"
2. Allow unit time to cool (at least 5 minutes).
3. Remove all attachments and accessories from unit.
4. Remove Water Tank Cap and drain any remaining water from Water Tank into a sink or tub to
minimize potential mineral build-up. Replace Water Tank Cap when done.
5. Collapse Extension Pole to shortest length and wrap power cord around Cord Brackets.
6. Store 3-in-1 Steam Mop in a cool, dry location, along with all included accessories.
MINERAL BUILD-UP
A common maintenance need for steam appliances is the removal of build-up caused by high
mineral content in many municipal water supplies. This mineral build-up may limit the
effectiveness and reduce the life of your 3-in-1 Steam Mop.
The best way to minimize mineral build-up is to use distilled or de-mineralized water when
using your 3-in-1 Steam Mop. In addition, it is recommended that the cleaning procedure below
be followed at least once a month in order to remove any deposits that form. This will help to
extend the life of your 3-in-1 Steam Mop and keep it functioning at its maximum potential.
To remove mineral build-up:
1. Follow STEPS 1-4 under Proper Storage section above. However, do not replace Water Tank
Cap at the end of STEP 4.
2. Insert tip of Cleaning Pin into opening of Steam Nozzle to remove mineral build-up in nozzle.
This may also be done to clean accessories such as the Jet Nozzle.
3. Fill included Measuring Cup with 3.5 oz. (100 ml.) distilled water and 1.5 oz. (50 ml.) vinegar.
4. Slowly pour water-vinegar solution into Water Tank through Fill Hole, then replace Water Tank Cap.
5. Plug in power cord and set Steam Control Dial to "HIGH". Allow unit to steam for 1 minute,
then set Steam Control Dial back to "OFF".
6. Allow unit to sit for approximately 30 minutes, then set Steam Control Dial back to "HIGH" and
allow the remainder of the Water Tank's contents to be steamed out.
7. Once Water Tank is drained, turn unit off and refill Tank with 15 oz. (450 ml.) of fresh distilled
water. Set Steam Control Dial back to "HIGH" and allow unit to steam until Water Tank is empty.
Repeat as necessary until vinegar odor dissipates.
8. Set Steam Control Dial to "OFF", unplug power cord and store 3-in-1 Steam Mop as usual.
IMPORTANT: On average, it is recommended that you follow the mineral build-up removal
procedure once per month (if unit is used once every week). More frequent use may require
following the procedure more often in order to keep your 3-in-1 Steam Mop operating at
full potential. Do not exceed 20 hours of use without cleaning out mineral build-up.
ENGLISH | 15