Initial Operation/Setting; Battery Pack; Switching On And Off - Metabo PowerMaxx SSD 12 Manual Original

en ENGLISH
Collect the particles generated at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream towards yourself or nearby
persons or towards dust deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep
it clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash protective clothing. Do not blow,
beat or brush protective gear.
Transport of li-ion battery packs:
The shipping of li-ion battery pack is subject to laws
related to the carriage of hazardous goods (UN
3480 and UN 3481). Inform yourself of the currently
valid specifications when shipping li-ion battery
packs. If necessary, consult your freight forwarder.
Certified packaging is available from Metabo.
Only send the battery pack if the housing is intact
and no fluid is leaking. Remove the battery pack
from the machine for sending. Prevent the contacts
from short-circuiting (e.g. by protecting them with
adhesive tape).
5. Overview
See page 2. (sample figure)
1 Hexagon socket attachment for hexagon
screwdriving bits
2 Locking sleeve
3 Rotation selector switch / Transporting safety
device
4 Trigger
5 LED light
6 Button for speed/tightening torque preselection
*

7 Battery pack *

8 Capacity indicator button *
9 Capacity and signal indicator *
10 Handle (gripping surface)
11 Battery pack release button
12 Belt hook (attach as shown) *
13 Bit depot (attach as shown) *
* depending on the features / model

6. Initial Operation/Setting

Remove battery pack from the machine before
carrying out any setting, retrofitting,
maintenance or cleaning. Ensure that the machine
is switched off when the battery pack is switched
off.
10
6.1 The machine's multifunctional
monitoring system
If the machine switches off automatically, the
machine electronics have activated automatic
protection mode. A warning signal sounds
(continuous beeping). The beeping stops after a
maximum of 30 seconds or when the trigger switch
(4) is released.
In spite of this protective function, overloading
is still possible with certain applications and
can result in damage to the machine.
Causes and remedies:
1. Battery pack almost flat (the electronics
prevent the battery pack from discharging totally
and avoid irreparable damage).
If the battery pack is almost flat, it must be
recharged.
2. Long continuous overloading of the machine will
activate the temperature cut-out.
Leave the machine or battery pack to cool.
Note: the machine will cool more quickly if you
operate it at idling speed.
6.2 Battery pack
Charge the battery pack (7) before use. Charge the
battery pack again if the performance drops.
Instructions on charging the battery pack can be
found in the operating instructions of the Metabo
charger.
Li-Ion battery packs "Li-Power, LiHD" have a
capacity and signal indicator (9):
- Press the button (8), the LEDs indicate the charge
level.
- The battery pack is almost flat and must be
recharged if one LED is flashing.
Removing:
Press the battery pack release button (11) and pull
the battery pack (7) forwards.
Inserting:
Slide in the battery pack (7) until it engages.
6.3 Setting the direction of rotation,
engaging the transporting safety device
(switch-on lock)
Only operate the rotation selector switch /
transporting safety device (3) when the motor
is at standstill!
Actuate the rotation selector switch / Engage the
transportation lock (3).
R = Clockwise setting
(drive in screws)
L = Anti-clockwise setting
(undo screws)
0 = middle position: transportation safety device
(Switch-on lock) set
6.4

Switching on and off

Switching on: press the trigger switch (4).
Switching off: Release the trigger (4).