Step 1 Remove Packaging; Step 2 Install Water Line; Electric Shock Hazard; Peligro De Descarga Eléctrica - Monogram FZIR360NNRH Instrucciones De Instalación

Installation Instructions - Standard Installation

STEP 1 REMOVE PACKAGING

WARNING
is much heavier at the top than at the bottom – be careful
when moving. When using a hand truck, handle from side
only.
AVERTISSEMENT
basculement Le produit est beaucoup plus lourd en haut
qu'en bas. Il faut être prudent lors des déplacements. Si un
diable est utilisé, il faut soulever le réfrigérateur sur le côté
seulement.
ADVERTENCIA
producto es mucho más pesado en su parte superior que en
su parte inferior – tenga cuidado al moverlo. Al usar un carro
manual, sosténgalo de costado únicamente.
• Carefully cut banding at the top and bottom, remove
outer carton.
• Slide out back corner posts (2).

STEP 2 INSTALL WATER LINE

WARNING
Connect to potable water supply only.
A cold water supply is required for automatic icemaker
operation. The water pressure must be between 40
and 120 psi (275-827 kilopascals).
WARNING

ELECTRIC SHOCK HAZARD

Attach tubing clamp using existing hole only. DO NOT
drill into the refrigerator.
AVERTISSEMENT
alimentation d'eau potable seulement. Une alimentation
d'eau froide est requise pour faire fonctionner
la machine à glaçons et le pichet à remplissage
automatique. La pression d'eau doit se situer entre 40 et
120 psi. (275 à 827 kPa).
AVERTISSEMENT
Fixez le collier de serrage dans le trou présent seulement.
NE PERCEZ PAS dans le réfrigérateur.
ADVERTENCIA
Realice la conexión a un
suministro de agua potable únicamente. Se requiere
un suministro de agua fría para el funcionamiento de la
máquina de hielos automática y de la jarra de llenado
automático. La presión del agua deberá estar entre 40 y
120 p.s.i. (275 – 827 kPa).
ADVERTENCIA
Adhiera la abrazadera de la tubería usando el agujero
existente únicamente. NO perfore el refrigerador.
Tip Over Hazard.
Product
Risque de
Riesgo de Caída El
Raccordez l'appareil à une
RISQUE DE DÉCHARGE
ÉLECTRIQUE
PELIGRO DE DESCARGA
ELÉCTRICA
• Slide carton off top of cabinet.
NOTE: IT IS NOT NECESSARY TO LAY CABINET
DOWN IN ORDER TO REMOVE SKID!
NOTE: DO NOT ATTEMPT TO ROLL UNIT OFF SKID.
• The unit is secured to the skid
with 4 slotted tie-down straps.
Remove the four 5/16" bolts
from the base channels in the
tie-downs.
• Remove toekick, and wall
bracket. Set aside for final
installation.
• Lift the unit off the skid with an
appliance dolly. Handle from
the sides.
• Remove the four 7/16" bolts securing the tie-down
brackets to the skid.
• Route 1/4" OD copper or SmartConnect
tubing between house cold water line and the water
connection location.
• Tubing should be long enough to extend to the front of
the unit. Allow enough tubing to accommodate bend
leading into the water line connection.
NOTE: The only Monogram approved plastic tubing is
supplied in the SmartConnect
Do not use any other plastic water supply line because
the line is under pressure at all times. Other types of
plastic may crack or rupture with age and cause water
damage to your home.
SmartConnect ™ Refrigerator Tubing Kits are available in
the following lengths:
2' (.6 m) WX08X10002
15' (4.6 m) WX08X10015
8' (2.4 m) WX08X10006
25' (7.6 m) WX08X10025
14
™
plastic
™
Refrigerator Tubing kits.
31-1000416 Rev. 0