Before You Call For Service - JENN-AIR JGA8100 Serie Guia Del Usuario

B
EFORE
F
OR MOST CONCERNS
:
FIRST
• Check if oven controls have been prop-
erly set.
• Check to be sure plug is securely inserted
into receptacle.
• Check or re-set circuit breaker. Check or
replace fuse.
• Check power supply.
P
ART OR ALL OF APPLIANCE DOES
.
NOT WORK
• Check if surface and/or oven controls
have been properly set. See pgs. 5 & 10.
• Check if oven door is unlocked after self-
clean cycle. See pg. 18.
• Check if oven is set for a delayed cook or
clean program. See pgs. 12 & 18.
• Check if Control Lock is activated. See pg.
16.
B
AKING RESULTS ARE NOT AS
EXPECTED OR DIFFER FROM
.
PREVIOUS OVEN
• Make sure the oven vent has not been
blocked. See pg. 8 for location.
• Check to make sure range is level.
• Temperatures often vary between a new
oven and an old one. As ovens age, the
oven temperature often "drifts" and may
become hotter or cooler. See pg. 16 for
instructions on adjusting the oven tem-
perature. NOTE: It is not recommended
to adjust the temperature if only one or
two recipes are in question.
• Check that oven temperature is decreased
by 25° F when convect baking.
• See "Cooking Made Simple" booklet
for more information on bakeware and
baking.
• Make sure oven is preheated when recipe
or directions recommend preheat.
• Check rack positions. See page 17.
F
OOD IS NOT BROILING PRO
PERLY OR SMOKES EXCESSIVELY
• Check oven rack positions. Food may be
too close to element.
• Aluminum foil was incorrectly used. Never
line the broiler insert with foil.
• Trim excess fat from meat before broiling.
Y C
OU ALL FOR
,
TRY THESE
• A soiled broiler pan was used.
O
VEN WILL NOT SELF
• Check to make sure the cycle is not set for
a delayed start. See pg. 18.
• Check if door is closed.
O
VEN DID NOT CLEAN PROPERLY
• Longer cleaning time may be needed.
• Excessive spillovers, especially sugary and/
or acid foods, were not removed prior to
the self-clean cycle.
O
VEN DOOR WILL NOT UNLOCK
AFTER SELF
• Oven interior is still hot. Allow about one
hour for the oven to cool after the comple-
tion of a self-clean cycle. The door can be
opened when the LOC indicator word is
not displayed.
M
OISTURE COLLECTS ON OVEN
WINDOW OR STEAM COMES FROM
OVEN VENT
• This is normal when cooking or drying
foods high in moisture.
• Excessive moisture was used when clean-
ing the window.
S
URFACE OR GRILL BURNER FAILS
TO LIGHT
• Check to be sure burner ports or ignition
ports are not clogged. See page 20.
• Check to be sure ignitor is dry and clicking.
Burner will not light if ignitor is damaged,
soiled or wet. If ignitor doesn't click, turn
control knob OFF.
S
URFACE OR GRILL BURNER
FLAME LIFTS OFF PORTS
• Check to be sure a pan is sitting on the
grate above.
• Contact an authorized Jenn-Air servicer.
T
HE FLAME IS UNEVEN
-
• Burner ports may be clogged.
.
S
URFACE OR GRILL BURNER
FLAME IS YELLOW IN COLOR
• Contact an authorized Jenn-Air servicer.
• Some yellow tips on the flame are accept-
able when using LP gas.
S
ERVICE
- .
CLEAN
- .
CLEAN CYCLE
.
.
.
.
.
22
T
HERE IS A STRONG ODOR OR
LIGHT SMOKE WHEN OVEN IS
.
TURNED ON
• This is normal for a new range and will
disappear after a few uses. Initiating a
clean cycle will "burn off" the odors more
quickly.
.
• Turning on a ventilation fan will help
remove the smoke and/or odor.
• Excessive food soils on the oven bottom.
Use a self-clean cycle.
V
ENTILATION SYSTEM IS NOT
CAPTURING SMOKE EFFICIENTLY
• Check on cross ventilation in room or
make up air.
• Excessive amount of smoke is being cre-
ated; check instructions for grilling, trim-
ming meats. See pgs. 7 & 8.
• Outside wall cap may be trapped shut.
• Range may be improperly installed; check
ducting information. See pg. 4.
• Air filter may be improperly installed. See
pg. 8.
A
FAN SOUND CAN BE HEARD
• This is the cooling fan and is normal. The
fan will continue to run after use until the
oven cools.
"F"
PLUS A NUMBER AND THE
: "
MESSAGE CALL AN AUTHO
RIZED SERVICER OR 800-688-1100
• This is called a fault code. If a fault code
appears in the display and beeps sound,
press the Cancel pad. If the fault code
and beeps continue, disconnect power to
the appliance. Wait a few minutes, then
reconnect power. If fault code and beeps
still continue, disconnect power to the
appliance and call an authorized servicer.
• If the oven is heavily soiled, excessive
flare-ups may result in a fault code during
a clean cycle. Press Cancel pad and allow
the oven to cool completely. Wipe out
excess soil, then reset the clean cycle. If
the fault code and beeps still continue,
disconnect power to the appliance and
call an authorized servicer.
.
-
."