Philips 26PF5321 D/37 Guía De Uso Rápido página 34

Kensington Security Slot (if present)
Your TV is equipped with a Kensington Security Slot, to prevent it from getting stolen.
An anti-theft Kensington lock has to be purchased separately.
The Kensington lock is a plastic-coated steel cable with a lock. One end has to be fixed to the opening of the TV and locked with a
special key. The other end is attached to a fixed point.
® Kensington and MicmSaver are regJsteredUS trademarks of ACCO World Corporation with issued regJstmtionsand pending applic_tions in other
countnes throughout the world, All other registered and unregistered tr_demarks are the property of their respectiveowners,
Troubleshooting Tips
Symptoms
No display on screen
Possible Causes
Faulty power supply
TV's Power not turned
on
TV go to standby after
10min without video.
Faulty aerial and cable
Wrong source selected.
What you should do
Check whether power cord is properly connected into the mains socket. If there
is still no power, disconnect plug. Wait for 60 seconds and re-insert plug. Turn on
TV again.
Press the POWER key on the TV and wait for 10-15set.
Press the POWER key on the remote control,
Check whether euroconnector cables or aerial sockets are properly connected.
Check whether the source is correctly selected. Press AV+ button to enter
Source list and select the correct source.
Poor reception Faulty antenna connection • Faulty antenna connection
(snowish picture and Weak transmission
noise Wrong TV system Have you chosen the right TV system? (refer to page 5).
Reddish picture in Wrong setting of DVD Set the DVD player to the correct output video format.
AV11213 player
No sound Zero volume level Try increasing volume. (You will not see the volume indication if OSD set to
minimum)
Sound muted Check that the sound is not muted.
Aim remote control directly at sensor on front of TV.
Wrong audio selection Go to menu => Setup => Source => Analog Audio In => select AVI
Sound interference Electrical appliances Try turning off any electrical appliances, for example, hairdryer, vacuum cleaner
interference that are in use.
interference lines Wrong detection of Check whether power cord is properly connected
seen on S-Video signal Press the CH/PAGE +/- key on the remote control and do a channel up
followed by a channel down.
Make sure no composite video are connected on the same AV input.
intermittent or ,I_HDCP (see glossary) Noise is displayed if the connected digital equipment's (DVD player or set-up
flickering picture on authentication failed box) *HDCP authentication failed. Check user manual for the digital equipment
in HDHI you are connecting.
Use a HDMI compliant cable.
Try unplugging the HDHI cable and replugging it back.
Black bar on top and PC refresh rate too high Change PC refresh rate to 60 Hz.
bottom of screen in
PC mode
Picture position Slight differences in output . When displaying a High Definition signal from the YPbPr inputs or HDMI input, if
adjustment signals from different brands necessary, you can adjust the picture position to the center of the screen with the
and types of HD sources cursor lefdright or up/down buttons on the remote control.
Occasional appearance Characteristic of liquid This symptom is not a problem. The liquid crystal panel is built with very high and
black spots on the crystal panel precision technology giving you the fine picture details. Occasionally, a few
screen (LCD TV only) non-active pixels may appear on the screen as a fixed point of red, blue, green or
black. Note that this does not affect the performance of the set.
PC modes do not Wrong connections Check whether connections are correct.
work Wrong source selected. Check whether the source is correctly selected. Press AV+ button to enter
Source list and select the correct source.
Wrong display resolution Check whether you have configured the computer on a compatible display
resolution.
TV not responding Check if the remote control is in TV mode.
to Remote control Check if the green led blink when using remote control.
Wrong polarity of batteries " Check polarity of the batteries.
Flat batteries. Try changing the batteries.
26