Jacuzzi J-300 Serie Manual De Instalacion Y Uso & Mantenimiento página 28

To remove larger debris missed by the primary filtration system,
the control system can activate a secondary filtration system.
These cycles utilize Jets Pump 1 and the second filter cartridge
to quickly "skim" the water of large debris and minimize their
"bath-tub ring" effect.
B. For Models J-315/J-325
Your new spa includes a 24-hour primary filtration system, which
filters the water continuously (factory default). The circulation
pump draws water through the skimmer bag and one of the two
filter cartridges to effectively remove small debris in your spa. The
factory default setting is PF6. This setting should not be altered.
Running the circulation pump less than the factory recom-
mended time will result in issues with water quality maintenance.
Note: The 24-hour primary filtration system also supplies heated
water to the spa when the heater turns on.
To remove larger debris missed by the 24-hour primary filtration
system, you can program a secondary filtration system. The sec-
ondary filtration cycles use Jets Pump 1 and the second filter
cartridge to quickly "skim" the water of large debris and mini-
mize their "bath-tub ring" effect.
I
Programming the Primary Filtration Cycle
To make changes to the primary filtration cycle, follow the steps
below.
Press Press
PRESS PRESS
◄ ◄
PRESS PRESS
Press Press
A. Press the Menu (
settings. The LED screen will display "PF."
B. Press the Warmer (
the system for changes. The LED will display the last cycle pro-
grammed and will blink once to indicate the system is ready to
accept changes.
C. Press the Warmer (
through the cycles, PF0 to PF8.
D. Once a cycle is selected, press the Jets Pump 1 (
to confirm the selection. You must press the Jets Pump 1 (
button to confirm your selection or the current settings will re-
main active.
E. The display will show the new cycle selected and it will blink
twice to indicate that the change has been accepted.
Note: If no button is pressed within 5 seconds of each selection the
screen will revert back to the Main Menu and the current settings will
remain active.
Press Press Press
PRESS PRESS PRESS
◄ ◄
◄
PRESS PRESS
Press Press Press
) Button once to access the program
) or Cooler ( ) button to prepare
) or Cooler ( ) button to scroll
I
Programming the Change Filter Timer
Included within the Primary Filtration Menu, is the Change Filter
feature. To make changes to the change filter timer or to reset it,
follow the steps below.
PRESS
A. Press the Menu (
tration Menu. The LED screen will display "PF."
B. Press the Warmer (
Filtration cycles. After the last cycle, "PF8," the LED screen will
display the number of days remaining or zero.
Note: If you press the Warmer button after the number of days
remaining you will revert back to the "PF" menu. You will need to
repeat step B to re-enter the menu.
C. Press the Jets 1 (
Timer. The display on the LED screen will blink once to indicate
that the system is ready to accept changes.
D. Pressing the Warmer (
or subtract days in increments of 10 days. The range is from 0 to
180 days.
E. Once you select the number of days, press the Jets 1 (
button to confirm the selection. The display of the LED screen will
blink twice to indicate that the changes have been accepted. You
must press the Jets 1 (
the current settings will remain active.
PRESS
F. When the countdown timer reaches "0," the LED display will
flash between "CF" and the water temperature. At this time the
filters must be replaced or cleaned and the timer reset.
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current set-
tings will remain active.
I
Secondary Filtration Menu
The jets pump 1 activates during the secondary filtration to pro-
vide additional skimming. The spa is programmed with a default
setting of SF0 but can be programmed to any of the cycle settings
listed below. These cycles schedule the jets pump 1 to run for a
) button preset amount of time per day, in addition to normal operation.
Note: During the secondary filtration the jets pump 1, circulation
)
pump and CLEARRAY are activated.
28
Press
PRESS
Press
OR
OR
) button once to enter the Primary Fil-
) button to scroll through the Primary
) button to access the Change Filter
) or Cooler (
) button to confirm your selection or
No filtration
10 minutes of filtration every 12 hrs
10 minutes of filtration every 8 hrs
10 minutes of filtration every 6 hrs
Press
PRESS
) button will add
)