Programming A Wash 5 Thermal Cool-Down - Alliance Laundry Systems SF35PV Manual Del Usaurio

Programming
4. If Wash 1 is chosen, the no-reverse option may be
selected. The no-reverse option must be selected
at this point in the step programming. Press the
No Reverse key while the display reads
"W1nncc".
When the no-reverse option is selected, the
display will not indicate that the No Reverse key
is selected, but the machine will follow the
programming command.
The no-reverse option will cause the basket to run
forward only at wash speed for the time
programmed.
The computer will return to normal reversing
action when this step is complete.
The no-reverse option may be programmed in
wash, supply, heat, and overflow steps. The No
Reverse key must be pressed just prior to
pressing the Enter key when programming a step.
5. Press the Enter key, and the display will read
"M---S". Now assign the wash step time in
minutes and seconds.
6. Press the Enter key and go to the next step in the
cycle.
7. On machines equipped with optional auxiliary
heat (steam or electric), it is possible to program
a wash step with a temperature step. During such
a step, the machine will perform the programmed
wash at the temperature programmed,
maintaining that temperature throughout the step.
To program a wash with a specific temperature,
use the following procedure:
a. After step 3 of Programming a Wash Step,
press the Heat key before pressing the Enter
key. The display will read either "080Fcc" or
"025Ccc", depending on whether Fahrenheit
or Centigrade is prompted.
b. Now enter the desired temperature for the
machine to maintain during the wash step.
Three digits must be entered for the
temperature. If the desired temperature is less
than 100 degrees, the first digit must be 0. The
valid temperature range is 80-200 degrees
Fahrenheit and 25-93 degrees Centigrade. If
100 degrees Fahrenheit is selected, the display
will read "100Fcc".
c. Now proceed with step 5 above.
48
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming a Wash 5 Thermal
Cool-Down
After programming a heat step, it may be desirable to
program a temperature-controlled thermal cool-down
to gradually reduce the temperature of the load and
prevent fiber shock from sudden cool-down.
The temperature-controlled cool-down provides a
gradual cooling down from a higher temperature to a
lower temperature. The WE-6 monitors the
temperature of the water in the washer and attempts to
maintain an approximate cool-down rate of three
degrees per minute by periodically energizing the cold
water fill valve.
When the programmed time for the step expires, the
computer will advance to the next step regardless of
whether or not the cool-down temperature has been
reached. If the cool-down temperature is reached
before the time expires, the computer will advance to
the next step.
During the cool-down, the drain will remain closed
and water will exit through the overflow connection.
The cylinder will rotate in a normal reversing mode as
during a Wash 1 step.
Assuming that the computer is in the Program Mode
and that a heat step has been created and entered, use
the following procedure to program the thermal cool-
down. (Do not program a drain step before the Wash 5
step.)
1. Press the Wash key and then key 5. The display
will read "W5nncc".
2. Press the Enter key. The display will read either
"080Fcc" or "025Ccc", depending on whether
Centigrade or Fahrenheit is prompted.
3. Enter the desired temperature for the load to cool
down to. Three digits must be used for the
temperature. If the desired target temperature is
less than 100 degrees, the first digit must be 0.
The valid temperature range is 80-200 degrees
Fahrenheit and 25-93 degrees Centigrade. The
computer will not accept temperatures out of this
range. (The cool-down rate will be affected by
the temperature of the cold water available.) If
100 degrees Fahrenheit is selected, the display
will read "100Fcc".
F232059