Standard Equipment; Pre-Operation Inspection - RIDGID K-5208 Manual Del Usario

K-5208 Drain Cleaning Machine
Storage Temperature ........-20° F to 140° F (-29° C to 60° C)
Dimension L × W × H ........21.2" x 11.6" x 18.2"
(540 x 295 x 465 mm),
Handle in down position
Sound Pressure (L Drain Cleaner Weight ........54 lb. (24 kg) )* ......78.3 dB(A), K=3
PA
Sound Power (L )*...........83.5 dB(A), K=3
WA
* Sound measurements are measured in accordance with a standardized test per
Standard EN 62841-1.
- Sound emissions may vary due to your location and specific use of these tools.
- Daily exposure levels for sound need to be evaluated for each application and
appropriate safety measures taken when needed. Evaluation of exposure lev-
els should consider the time a tool is switched off and not in use. This may sig-
nificantly reduce the exposure level over the total working period.

Standard Equipment

All K-5208 Drain Cleaning machines come with one
RIDGID Drain Cleaning Mitt. Refer to the RIDGID cata-
log for details on equipment supplied with specific drain
cleaner catalog numbers.
NOTI E
This machine is made to clean drains. If prop-
erly used it will not damage a drain that is in good condi-
tion and properly designed, constructed and maintained.
If the drain is in poor condition, or has not been properly
designed, constructed and maintained, the drain cleaning
process may not be effective or could cause damage to
the drain. The best way to determine the condition of a
drain before cleaning is through visual inspection with a
camera. Improper use of this drain cleaner can damage
the drain cleaner and the drain. This machine may not
clear all blockages.

Pre-Operation Inspection

WARNING
Before each use, inspect your drain cleaning ma-
chine and correct any problems to reduce the risk of
serious injury from electric shock, twisted or broken
cables, chemical burns, infections and other causes
and prevent drain cleaner damage.
Always wear safety glasses, and other appropri-
ate protective equipment when inspecting your
drain cleaner.
1. Inspect the RIDGID drain cleaning mitts (Figure 3).
Make sure they are in good condition with no holes,
tears or loose sections that could be caught in the ro-
tating cable. It is important not to wear improper or
6
damaged mitts. The mitts
protect your hands from the
rotating cable and drain con -
tents. If the mitts are not
RIDGID drain cleaning mitts
or are damaged or worn out,
do not use machine until
RIDGID drain cleaning mitts
are available. Wear latex or
rubber gloves inside the mitt
to protect against drain con-
tents.
2. Make sure that the drain cleaning machine is un-
plugged and inspect the power cord, Ground Fault
Circuit Interrupter (GFCI) and plug for damage. If the
plug has been modified, or if the cord is damaged, to
avoid electrical shock, do not use the machine until the
cord has been replaced by a qualified repair person.
3. Clean the drain cleaner, including handles and con-
trols. This aids inspection and helps prevent the ma-
chine or control from slipping from your grip. Clean and
maintain the machine per the maintenance instruc-
tions.
4. Inspect the drain cleaning machine for:
• Proper assembly and completeness.
• Broken, worn, missing, misaligned or binding parts.
• Presence and readability of the warning label (see
Figure 1).
• Smooth and free movement of the clutch lever
handle. Slightly depress the clutch lever handle
and turn the lock pin clockwise (Figure 4) to release.
The clutch lever handle is spring loaded and will be
biased up when released.
LOCKED
Figure 4 – Releasing the Clutch Handle
• Confirm that the clutch and motor covers are se-
curely fastened to the drain cleaner and the motor
vents are clear. Do not operate without the covers
in place.
• Any other condition which may prevent safe and
normal operation.
If any problems are found, do not use the drain
cleaner until the problems have been repaired.
Figure 3 – RIDGID Drain
Cleaning Mitt
UNLOCKED
999-995-137.10_REV. B