Description, Specifications And Standard Equipment Description; Specifications - RIDGID K-400 Manual De Instrucciones

ating machine while in water increases the
risk of electrical shock.
If you have any question concerning this
RIDGID ® product:
– Contact your local RIDGID distributor.
– Visit RIDGID.com to find your local RIDGID
contact point.
– Contact Ridge Tool Technical Service De -
part ment at rtctechservices@emer son.com,
or in the U.S. and Canada call (800) 519-
3456.
Description,
Specifications and
Standard Equipment
Description
The RIDGID ® K-400 Drain Cleaning Machine
will clean drain lines from 1
100mm) in diameter and 100 feet (30,5m) in
length depending on size of the cable. Cor -
rosion-resistant cable drum holds 75 feet
(22,5m) of 1 / " (12mm) diameter cable or 100
2
feet (30,5m) of 3 / " (10mm) diameter cable.
8
Cable spins at 170 RPM. The K-400 is not
designed to remove root blockages.
The drum is belt-driven by a
motor that has a grounded electrical system.
An integral Ground Fault Circuit Interrupter
(GFCI) is built into the line cord. A FOR /OFF/ -
REV (or 1/OFF/2) switch controls drum and
cable rotation and a pneumatic foot switch
provides ON/OFF control of the motor.
The cable control system consists of a torque
limiter to stop the drum from rotating when
the tool stops rotating and the torque exceeds
the set value. This helps to prevent cable dam-
age from cable flip over in the drum. The torque
limiter is designed to work with RIDGID
and 1 / " integral wound (IW) cable, and may not
2
protect other cables.
The "Solid-Core" Integral Wound cable is
durable and kink-resistant. The cable has a
quick change coupling system for connect-
ing or disconnecting tools.
The optional AUTOFEED
the cable to be advanced or retrieved at a rate
of 12-15 feet per minute (3.6-4.6 m/minute).
999-998-156.09_REV. E
1 / " to 4" (40 to
2
1 / HP electric
3
3 / "
8
® cable feed allows
K-400 Drain Cleaning Machine
Warning Label
Folding
Handle
Belt
Guard
Wheels
RIDGID
Drain
Cleaning
Gloves
Tools
Figure 1 – K-400 Drum Machine

Specifications

Line Capacity .....1½" – 3" (40mm – 75mm)
Line with
3" – 4" (75mm – 100mm)
Line with ½" (12mm) Cable
The K-400 is not designed
to remove root blockages
Drum Capacity ...100' (30,5m) of
Diameter Cable
75' (22,5m) of
Diameter Cable
Motor Type..........Induction
120V~ Motor ......1/3 HP, 5A, 60Hz
220-240V~
Motor.....................230W, 2.5 A, 50 Hz
No Load Speed (n )
o
120V~.................170 RPM
220-240V~ .........140 RPM
Control ...............Rocker Type
FOR/OFF/REV switch and
pneumatic foot switch.
Some units have 1/OFF/2
Rotary Switch in place of
Rocker Switch.
Sound
Pressure (L )*......84.8 dB(A), K=3
PA
Sound
Power (L )* .........71.3 dB(A), K=3
WA
* Sound measurements are measured in accordance
with a standardized test per Standard EN 62481-1.
- Sound emissions may vary due to your location and
specific use of these tools.
- Daily exposure levels for sound need to be evaluated
for each application and appropriate safety measures
taken when needed. Evaluation of exposure levels
should consider the time a tool is switched off and not
in use. This may significantly reduce the exposure
level over the total working period.
FOR/OFF/REV
Switch
(1/OFF/2)
Cord Wrap
Drum
Cable
GFCI
3 / " (10mm) Cable
8
3 / " (10mm)
8
1 / " (12mm)
2
5