Noise Information; Declaration Of Conformity; General Safety Recommendations - Crown CT20101-18 Manual Original

Noise information

Always wear ear protection if the sound
pressure exceed 85 dB(A).

Declaration of conformity

We declare under our sole responsibility that
this product is in conformity with the regulations
2006/42/EC, 2004/108/EC, 2005/88/EC�
Certification
manager
Merit Link International AG
Stabio, Switzerland, 04.07.2017

General safety recommendations

CAUTION! Make sure you have read and
understood all the recommendations.
Failure to
recommendations may cause fire and /
or serious injuries.
• Do not operate this tool when tired, ill, or under the
influence of alcohol, drugs, or medication.
• Children and teens under the age of 15 must not use
the tool, except for teens guided by an adult�
• Inspect the tool before use. Replace all damaged
parts. Check for fuel leaks. Make sure all fasteners are
in place and secure� Any failure could cause personal
injury to the operator and bystanders, as well as
damage to the tool�
• Be aware of the risk of injury to the head, the hands
and the feet�
• Do not allow children and unauthorised persons near
places where operations with the use of the tool are
carried out� Third parties may distract the operator's
attention, and he may loose control over the tool�
Safety warnings for petrol tools
WARNING: Gasoline is toxic, highly
flammable, and its vapours can explode
if ignited.
Take the following precautions:
• do not smoke, keep sparks and open flames from
the area while adding fuel or operating the tool;
• store fuel only in containers specifically designed
and approved for the storage of such materials;
• avoid creating a source of ignition for spilled fuel�
Do not start the engine until the fuel vapours dissipate;
• always stop the engine and allow it to cool before
filling the fuel tank. Never remove the cap of the fuel
tank, or add fuel, when the engine is hot;
• never operate the tool without the fuel cap
securely in place. Loosen the fuel tank cap slowly to
relieve any pressure in the tank;
• mix and add fuel in a clean, well-ventilated area or
outdoors where there are no sparks or flames;
• move the tool at least 3m from the fuelling source
and site before starting the engine;
Wu Cunzhen
observe the following
• do not position flammable or nylon / fabric objects
near and / or on the tool;
• close the fuel tank plug tightly to avoid leakages
of fuel and escape of fuel's vapors;
• if in the process of fueling the tool you have
spilled fuel or oil on it, carefully wipe the tool;
• if in the process of fueling the tool you have
spilled fuel or oil on yourself, change your clothes
and carefully wash parts of your body in contact with
the fuel or oil, using water with soap�
Safety regulations
operations
• Breathing exhaust fumes can be lethal� Operate
this tool only in a well ventilated area and never in
places affected by dust, acids, vapours, explosive or
flammable gases.
• Use personal protection equipment� Always wear
protective goggles� When necessary, use respirators,
non-slipping boots, hard hats and earplugs� Long
sleeve shirts are recommended� The use of personal
protection equipment is one of the factors that reduce
the risk of injuries.
• Do not wear loose clothing, jewellery, short pants,
sandals or go barefoot� Hair, garment parts and gloves
should be protected against contact with the moving
parts of the tool�
• Use the tool only in daylight or good artificial light.
• Avoid accidental starting� Do not apply excessive
force, take a stable position and always try to keep
balance this will facilitate control over the tool�
• Stop and switch the engine to off for maintenance,
repair, or for changing parts�
• Do not use parts, accessories or attachments which
are not authorised for this tool� Doing so could lead to
serious injury to the user, or damage to the tool, and
void your warranty�
• To reduce a fire hazard, replace the faulty muffler
and spark arrestor, keep the engine and muffler free
from grass, leaves, excessive grease or carbon build
up�
Safety regulations for using the tool
• Stop the engine immediately if you feel an excessive
vibration. Vibration is a sign of trouble. Inspect
thoroughly for loose nuts, bolts or damage before
continuing� Repair or replace all affected parts as
necessary�
• Tools are to be used only in operations, for which
they have been designed, which will ensure safety and
help achieve better results�
• Keep hands, face, and feet at a distance from all
moving parts�
• Do not touch the engine or muffler. These parts get
extremely hot from operation� When turned off they
remain hot for a short time�
• Always stop the engine while taking a break.
• If you strike or become entangled with a foreign
object, stop the engine immediately and check for
damage� Do not operate before repairing the damage�
Do not operate the tool with loose or damaged parts�
Service of the tool
• Keep the tool clean. Never clean the tool with
flammable liquids or solvents.
• Your tool should be serviced only by qualified
specialists, with the use of recommended spare parts�
English
13
during the preparatory