General Safety Precautions; Machinery Directive - entrematic Ditec CROSS30 Manual De Instalación Y Mantenimiento

GENERAL SAFETY PRECAUTIONS

This installation manual is intended for professionally
competent personnel only.
Installation, electrical connections and adjustments must be
performed in accordance with Good Working Methods and in
compliance with applicable regulations.
Before installing the product, carefully read the instructions. Bad
installation could be hazardous.
The packaging materials (plastic, polystyrene, etc.) should not
be discarded in the environment or left within reach of children,
as these are a potential source of hazard.
Before installing the product, make sure it is in perfect condi-
tion.
Do not install the product in an explosive environment and atmos-
Before installing the motors, make all structural changes relating
to safety clearances and protection or segregation of all areas
where there is risk of being crushed, cut or dragged, and danger
areas in general.
Make sure the existing structure is up to standard in terms of
strength and stability.
The motor manufacturer is not responsible for failure to use
Good Working Methods in building the frames to be motorised
or for any deformation occurring during use.
The safety devices (photocells, safety edges, emergency stops,
etc.) must be installed taking into account: applicable laws and
directives, Good Working Methods, installation premises, sys-
tem operating logic and the forces developed by the motorised
door or gate.
The safety devices must protect any areas where the risk exists
of being crushed, cut or gragged, or where there are any other
risks generated by the motorised door or gate. Apply hazard
area notices required by applicable regulations.
the motorised door or gate.
Before making power connections, make sure the plate
details correspond to those of the power mains.
Fit an omnipolar disconnection switch with a contact opening
gap of at least 3 mm. Make sure an adequate residual current
electrical system.
When necessary, connect the motorised door or gate to a reliable
earth system made in accordance with applicable safety regula-
tions. During installation, maintenance and repair, interrupt the
power supply before opening the lid to access the electrical parts.
To handle electronic parts, wear earthed antistatic conduc-
tive bracelets.
The motor manufacturer declines all responsibility in the event
safe an correct operation.
For repairs or replacements of products only original spare parts
must be used.
The installer shall provide all information relating to automatic,
manual and emergency operation of the motorised door or gate,
and provide the user with operating instructions.

MACHINERY DIRECTIVE

Pursuant to the Machinery Directive (2006/42/EC), the installer
who motorises a door or gate has the same obligations as the
manufacturer of machinery and as such must:
- prepare the technical data sheet which must contain the docu-
ments indicated in Annex V of the Machinery Directive;
(the technical data sheet must be kept and placed at the dis-
posal of competent national authorities for at least ten years
from the date of manufacture of the motorised door or gate);
- draw up the EC Declaration of Conformity in accordance
with Annex II-A of the Machinery Directive and deliver it to the
customer;
ance with point 1.7.3 of Annex I of the Machinery Directive.
APPLICATIONS
Service class: 5 (minimum 5 years of working life with 600
cycles a day)
Use: HEAVY DUTY (For vehicle or pedestrian accesses to
institutional complexes with very intense use).
commended weight (about 2/3 of maximum allowed weight).
Use with maximum allowed weight could reduce the above
- The service class, operating times and number of conse-
cutive cycles are merely approximate. These have been
statistically determined in average conditions of use and
are not certain for each single case. They refer to the pe-
riod when the product operates without the need for special
maintenance.
- Each automatic entrance features variable factors such as:
friction, balancing and environmental conditions that can
substantially change both the duration and operating quality
of the automatic entrance or part of its components (including
automatic system). It is up to the installer to adopt adequate
DECLARATION OF INCORPORATION OF
PARTLY COMPLETED MACHINERY
(Directive 2006/42/EC, Annex II-B)
The manufacturer Entrematic Group AB, with headquarters in
Lodjursgatan 10, SE-261 44 Landskrona, Sweden, declares
that the Ditec CROSS30 automation for sliding gates:
- is designed to be installed on a manual gate to form a ma-
chine pursuant to Directive 2006/42/EC. The manufacturer
of the motorised gate must declare conformity with Directive
2006/42/EC (annex II-A) prior to initial machine start-up;
- complies with the applicable essential safety requirements
indicated in Annex I, Chapter 1 of the Directive 2006/42/EC;
- complies with the Electromagnetic Compatibility Directive
2014/30/EU;
- complies with the RED Directive 2014/53/EU;
- the technical documentation complies with Annex VII-B of the
Directive 2006/42/EC;
- the technical documentation is managed by the Technical
Boccioni 1 – 21040 Origgio (VA) – ITALY) and is available
upon request, sending an e-mail to ditec@entrematic.com ;
- a copy of the technical documentation will be given to compe-
Landskrona, 01-07-2016
9
-
-
Matteo Fino
(Chairman)
CROSS30 - IP1777