Stanley STSP125 Manual De Instrucciones página 14

14 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits
etc., in accordance with these instructions taking
into account the working conditions and the work
to be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
STANLEY Service Center or an equally qualified
person in order to avoid damage or injury. If the
power cord is replaced by an equally qualified
person, but not authorized by STANLEY, the
warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........ Volts
n .......
0
A ........ Amperes
Hertz
...... Class II
Watts
....
minutes
..... Alternating
....
Current
..... Direct
.../min..
Current
No-Load
Speed
ADDITIONAL SAFETY PRECAUTIONS
Caution! Do not touch exposed metal parts of the
tool when cutting through walls and floors, or when in
contact with electrical wiring. Hold the tool by insulated
gripping surfaces when performing an operation
where the cutting tool may come in contact with
concealed wiring or its own cord. Contact with a "live"
wire will make exposed metal parts of the tool "live" and
this will cause electric shock to the operator.
f Always keep your hands away from the cutting
area and the diamond wheel. Always keep the other
hand on the side handle. If you hold the tool with
both hands, you will not be injured by the wheel.
f Do not touch the underside of the workpiece
because the guard cannot protect the part of the
wheel under the workpiece.
f Always use a diamond wheel with wellmatched
size and center (diamond or circular shape).
Mismatched wheel and holder will result in eccentric
operation and you may lose control.
f Do not use any washer or bolt that is damaged
or unfit in size; otherwise you will lose control
of the operation.
f Do not use any grinding wheel.
f Do not use any diamond wheel that does not
conform to the manufacturer's stipulations.
f Do not use any cutting wheel that has been
damaged, distorted, or cracked.
f Do not operate the tool without the fixed guard.
f Do not start the tool with the cutting wheel
touching the workpiece.
f After switching off the tool, put down the
tool only after the cutting wheel has completely
stopped running. Do not force the wheel to stop.
f Disconnect the plug from the power source
and ensure that the diamond wheel is stationary
before replacing it, adjusting the cutting depth
or water pipe, or repairing the tool.
f Only hold the tool by its insulated gripping
surface when the diamond wheel is likely to cut
through concealed wires or its own cord. If the
diamond wheel touches a "live" wire, the exposed
metal parts of the power tool may be charged and
thus cause electric shock to the operator.
Construction
f Be extra cautious when "blind cutting" through
Earthing
walls or other blind areas because the diamond
Terminal
wheel may cut into gas or water piping, wires,
Safety Alert
Symbol
or resilient objects.
Revolutions
or Recipro-
cation per
minute
FOR MARBLE CUTTERS