GE Evolve E2SA Guia De Instalacion
GE Evolve E2SA Guia De Instalacion

GE Evolve E2SA Guia De Instalacion

Luminaria de seguridad evolve led

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

GE
Lighting
Evolve
LED Security Light (E2SA)
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
Save these instructions for future use.
Risk of electrical shock. Disconnect power before servicing
or installing product.
Risk of injury or damage. Unit will fall if not installed
properly. Follow installation instructions.
Risk of injury. Wear safety glasses and gloves during
installation and servicing.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This Class [A] RFLD complies with the Canadian standard ICES-003.
Ce DEFR de la classe [ A ] est conforme à la NMB-003 du Canada.
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
imagination at work
LED Security Lighting
WARNING
WARNING
CAUTION
• This luminaire is designed for outdoor lighting
service, and should not be used in areas of limited
ventilation, or in high ambient temperatures.
• Best results will be obtained if installed and maintained
according to the following recommendations.
• Luminaire is designed to operate in typical
temperatures at 25°C and to be mounted
horizontally with LEDs facing down, as shown.
SPECIFICATIONS:
• Weight: Maximum weight <16 lbs with std 24"
mounting arm
• Dimensions:
L x W x H
W/O Refractor: 10.9 in x 10.9 in x 8.4 in
(277mm x 277mm x 213mm)
W Refractor:
10.9 in x 10.9 in x 11.2 in
(277mm x 277mm x 279mm)
• IP Rating:
Wet location (IP65 for optical)
Installation Guide
GEH-6028

Publicidad

Tabla de contenido
loading

Resumen de contenidos para GE Evolve E2SA

  • Página 1 Installation Guide GEH-6028 Lighting Evolve LED Security Lighting ™ LED Security Light (E2SA) BEFORE YOU BEGIN Read these instructions completely and carefully. Save these instructions for future use. WARNING Risk of electrical shock. Disconnect power before servicing or installing product. •...
  • Página 2 3b. INSTALLATION UNPACKING Tighten nut to secure mounting arm to pole. Insert lag • This luminaire has been properly packed so that no bolts in outer lower holes of mounting arm. Hammer parts should have been damaged during transit. in lag bolts to approximately 1” of head then tighten •...
  • Página 3 WIRING NOTE: Make all electrical connections in accordance with the National Electrical Code and any applicable local code requirements including grounding. NOTE: Verify that supply voltage is correct by comparing it to nameplate. CAUTION Risk of Burn: Allow light engine/fixture to cool before handling. •...
  • Página 4: Maintenance / Cleaning

    (1 - 888 - 69 - 43 - 533) GE Lighting Solutions, LLC is a subsidiary of the General Electric Company. Evolve and the GE brand and logo are trademarks of the General Electric Company. © 2014 GE Lighting Solutions, LLC. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.
  • Página 5: Éclairage De Sécurité Led Evolve

    Guide d’installation GEH-6028 Lighting Éclairage de sécurité LED Evolve ™ Lampe de sécurité LED (E2SA) AVANT DE COMMENCER Lire entièrement et attentivement ces instructions. Conserver ces instructions pour usage ultérieur. AVERTISSEMENT Risque d’électrocution. Débrancher l’alimentation avant Remarque: Cet appareil a été testé et reconnu conforme d’installer ou d’effectuer l’entretien de ce produit.
  • Página 6 3b. INSTALLATION DÉBALLAGE Visser l’écrou pour fixer le bras de montage au poteau. • Ce luminaire a été adéquatement emballé afin qu’aucune Insérer les tirefonds dans les extrémités extérieures en bas pièce ne s’endommage pendant l’expédition. du bras de montage. Enfoncer les tirefonds au marteau •...
  • Página 7 CÂBLAGE REMARQUE : Effectuer tous les raccords électriques conformément au Code électrique national et aux exigences de code local applicables, notamment les exigences de mise à la terre. REMARQUE : S’assurer que la tension d’alimentation est adéquate en comparant avec la plaque signalétique. ATTENTION Risque de brûlure : Laisser refroidir l’appareil l’éclairage et son moteur avant de les manipuler.
  • Página 8: Maintenance / Nettoyage

    (1 - 888 - 69 - 43 - 533) GE Lighting est une filiale de General Electric Company. Les marques et logos Evolve et GE sont des marques de commerce appartenant à General Electric Company. © 2014 GE Lighting. Les informations fournies peuvent faire l’objet de modifications sans préavis. Toutes les valeurs sont des valeurs de calcul ou valeurs typiques lorsqu’elles sont mesurées en conditions de laboratoire.
  • Página 9: Luminaria De Seguridad Evolve

    Guía de Instalación GEH-6028 Lighting Luminaria de Seguridad Evolve ™ Luminaria de Seguridad (E2SA) ANTES DE EMPEZAR ALTO Lea estas instrucciones por completo y detenidamente. Guarde estas instrucciones para uso futuro. ADVERTENCIA Riesgo de descarga eléctrica. Desconecte la fuente de luz antes de dar mantenimiento o al instalar el producto.
  • Página 10: Montaje

    3b. INSTALACIÓN DESEMPAQUE Apriete la tuerca para asegurar el brazo de montaje al • Esta luminaria ha sido empacada adecuadamente poste. Inserte pernos de fijación en los agujeros inferiores para que ninguna parte se dañe durante su envío. exteriores del brazo de montaje. Amartille los pernos de •...
  • Página 11 CABLEADO NOTA: Todas las conexiones eléctricas deberán realizarse de acuerdo con el Código Eléctrico Nacional y conforme a códigos locales correspondientes, incluyendo puesta a tierra. NOTA: Verifique que el voltaje de alimentación sea el correcto comparándolo con la placa del fabricante. PRECAUCIÓN Riesgo de quemadura: Permita que el dispositivo o máquina de luz se enfríe antes de tocarlo.
  • Página 12: Mantenimiento / Limpieza

    GE Soluciones de Iluminación, LLC es una subsidiaria de la Compañía General Electric. Evolve y la marca y logotipo de GE son marcas registradas de la Compañía General Electric. © 2014 GE Soluciones de Iluminación. La información se encuentra sujeta a cambio sin previo aviso. Todos los valores son de diseño, o valores típicos al momento de ser medidos bajo condiciones de laboratorio.

Tabla de contenido