Brilix JET SWIM ELEGANCE 70 Guía De Instalación Y Usuario página 5

3. Jet swim body installation
3.1 Installation of jet swim device body in concrete ground
Stick hoses (no. 21 picture 3) on the 'jet swim' body (no. 20 picture 3) and connect them into the technologic
device area (basin). Protect the hose endings against the concrete. Carry out the 'jet swim' body installation
no. picture 20 3 as indicated in the picture 2a into the hole made in a concrete wall or into the boarding for
concreting without a flange or padding. If the body is fixed to the wall, follow the instructions in the article
4 and install the pneumatic and air connection.
3.2 Installation of jet swim device body in concrete pools with foil
While mounting the 'jet swim' body into the walls of a concrete pool with foil, please follow the instruction
written in the chapter no. 2 and 3. You can start to mount the padding and the 'jet swim' flange picture 2b.
into the pool while fixing the 'jet swim' body into the wall of a pool. 2b.
Tighten the padding (no. 18 in the picture 3) into the 'jet swim' body (no. 20 in the picture 3) by 2 screws
(no. 19 in the picture 3) and bear in mind that the pool foil can be situated between two padding (picture 2b).
Fix the flange in the end (no. 17 in the picture 3) and tighten the screws (no. 16 in the picture 3), after this
step is done, cut the foil from the inside part of the flange.
During the installation of the air and pneumatic lead, take the steps according to the article 4.
3.3 Installation of jet swim device body in panel or sheetmetal pool with foil
Prepare the opening of 270 mm diameter in the wall pool in a way that the centre of a jet is approximately
30cm under the water level as described in the article 2 and picture 1. Place the 'jet swim' body no.20 picture
3 from the inside part of the pool into the prepared opening. Fix the body by 8 self-drilling screws no. 19
picture 3 into the wall of the pool as described in the picture 2c.
Tighten the padding (no. 18 in the picture 3) to the 'jet swim' body (no. 20 in the picture 3) by 2 screws
(no. 19 in the picture 3) After the installation of the foil, fix the flange (no. 17 in the picture 3) and tighten
the screws (no. 16 in the picture 3), then cut the foil from the inside part of the flange.
During the installation of the air and pneumatic lead, take the steps according to the article 4.
3.4 Installation of the swim jet body to the preformed (polypropylene) pool
Prepare the opening of 230 mm diameter in the wall pool in a way that the centre of a jet is approximately
30cm under the water level as described in the article 2 and picture 1.
Stick the padding (no. 18 in the picture 3) from the inside part of the pool wall and prepare openings for
16 screws of the flange (no. 16 picture 3).
Prepare the 'jet swim' body (no. 20 picture 3) from the inside part of the pool and tighten the flange
(no. 17 in the picture 3) by screws (no. 16 in the picture 3) from the inside part as described in the picture 2d.
During the installation of the air and pneumatic lead, take the steps according to the article 4.
3.5 Installation of the swim jet body to a prefabricated pool should be carried out in compliance
with the pool manufacturer. The mounting may differ from the recommendations of the swim jet
manufacturer. It may also be in a different location according to the individual types and dependent
on the design of the swimming pool form.
5
EN