Operation - Parkside ZKGS 2100 Instrucciones De Utilización Y De Seguridad

Anleitung_4300689:_ 24.11.2009
GB/
MT
you can tilt the machine head (5) to the left
by up to 45° (Fig. 1-2).
Screw the additional stability bar (18) to the
back of the equipment (Fig. 6).
7.3 Precision adjustment of the stop for
crosscut 90° (Fig. 7-8)
No stop angle included.
Fasten the turntable (16) in 0° position.
Undo the locking screw (23) and move the
machine head (5) all the way to the right
using the handle (1).
Place the 90° angular stop (z) between the
blade (7) and the turntable (16).
Slacken the counternut (d). Adjust the
adjustment screw (90°) (29) until the angle
between the blade (7) and the turntable (16)
equals 90°.
Retighten the counternut (d) to secure this
setting.
Check the position of the pointer (21) on the
scale (20). If necessary, release the pointer
(21) with a crosstip screwdriver, move to the
0° position of the scale (20) and retighten.
7.4 Precision adjustment of the stop for
miter cut 45° (Fig. 1, 7, 10-11)
No stop angle included.
Fasten the turntable (16) in 0° position.
Undo the locking screw (23) and move the
machine head (5) all the way to the left
using the handle, until it coincides at 45°.
Place the 45° stop angle (y) between the
blade (7) and the turntable (16).
Adjust the adjustment screw (30) so that the
angle between the blade (7) and the
turntable (16) equals exactly 45°.

8. Operation

8.1 Cross cut 90° and turntable 0°
(Fig. 1-3, 12)
Important! The integral resetting springs will
automatically lift the machine head. Do not
simply let go of the handle (1) after cutting, but
allow the machine head (5) to rise slowly,
applying slight counter pressure as it does so.
46
16:22 Uhr Seite 46
For cutting widths up to approx. 100 mm it is
possible to fix the saw's drag function with the
locking screw for drag guide (24) in rear
position. If the cutting width exceeds 100 mm
you must ensure that the locking screw for drag
guide (24) is slackened and that the machine
head (5) can be moved.
Move the machine head (5) to its upper
position.
Use the handle (1) to push back the
machine head (5) and fix it in this position if
required (dependent on the cutting width).
Place the piece of wood to be cut at the stop
rail (19) and on the turntable (16).
Lock the material with the clamping device
(8) on the fixed saw table (17) to prevent the
material from moving during the cutting
operation.
Push down the release lever (3) to release
the machine head (5).
Press the ON/OFF switch (2) to start the
motor.
With the drag guide (26) fixed in place: use
the handle (1) to move the machine head
(5) steadily and with light pressure
downwards until the saw blade (7) has
completely cut through the workpiece.
With the drag guide (26) not fixed in place:
pull the machine head (5) all the way to the
front. Lower the handle (1) to the very
bottom by applying steady and light
downward pressure. Now push the machine
head (5) slowly and steadily to the very
back until the saw blade (7) has completely
cut through the workpiece.
When the cutting operation is completed,
move the machine head (5) back to its
upper (home) position and release the
ON/OFF button (2).
8.2 Cross cut 90° and turntable 0° - 45°
(Fig. 1-3, 13)
The crosscut saw can be used to make
crosscuts of 0° -45° to the left and 0° -45° to the
right in relation to the stop rail.
Release the turntable (16) by slackening the
locking grip (13).
Press the latched position lever (12). Turn
the turntable (16) and scale pointer (14) to
the desired angular setting on the scales