Technical Specifications; Ec Declaration Of Conformity - Bircher CareMat Traducción Del Manual De Instrucción Original

Radio system combined with cable-connected light signalling system
6
Configuration RCL07 radio receiver
6 1
The plug connection of the RCL07 to the call
system must be installed by a qualified techni-
cian. One CareMat and one RCL07 radio recei-
ver are installed per room. If anyone steps on
an assigned CareMat, an alarm signal is trans-
mitted to the RCL07. The LED illuminates and
the relay output reacts. The CareMat continu-
es to transmit for as long as it is activated and
in any case for a maximum of 10 seconds. The
LED does not illuminate in the stand-by mode.
The deadman's operation is factory set.
Programming the radio transmitter
6 2
To tune-in the CareMat on the RCL07: Press the programming key briefly
(< 1.6 seconds). The LED then clashes. Tune-in the CareMat by actuating it.
When the programming is successfully completed the LED illuminates. To return
to the operating mode briefly press the programming key once more.
To switch-off CareMat on RCL07: press the programming key for longer than
1.6 seconds until the LED starts to flash rapidly. The switching-off mode is acti-
vated. Then actuate CareMat. The LED illuminates briefly. The CareMat is now
switched-off. To return again to the operating mode, press the programming key
briefly.
Note: The CareMat and the signal transmitter form a call system. They
should be clearly identified so that they cannot be mixed up. In this way, it
can be ensured that the call is only triggered in the particular room where
the CareMat and the RCL07 are also actually located.
7 Maintenance and fault finding
Apart from battery changing the CareMat is maintenance-free. Only tighten
the screws lightly.
If despite this, function is not being provided, the following checks should be
made:
• Is the call system operating and the RCL07 correctly connected?
• Is the CareMat correctly tuned-in to the RCL07?
• Is the signal transmitter battery OK?
If the points mentioned above have been checked out, but the functions of
the CareMat are, despite this, still not being provided, you should consult a
qualified expert.
9

Technical specifications

Article
Dimensions (LxWxH)
Weight [kg]
Material
Colour
Surface
Weight of persons
Chemical resistance
10 EC-Declaration of Conformity
Manufacturer:
Following directives have been observed:
Product variants:
Contact | Seller
11
Bircher Reglomat AG, Wiesengasse 20, CH-8222 Beringen, www.bircher-reglomat.com
4
Output Relay (two-way contact)
max. contact load 30 V DC / 1A
CareMat Ax1T E868 / Bx1T E868 / Cx1T E868
1100x700x9 mm / 700x400x9 mm / 1100x700x9 mm,
height with housing 15 mm
8.2 kg / 3.2 kg / 6.5 kg
Polyurethane (PU)
Careyellow, Caregrey
Stud texture design
At least 10 kg
Water (room temp.), body fluids, customary disinfectants,
max. 70 vol% alcohol
Bircher Reglomat AG, Wiesengasse 20, CH-8222 Beringen
RoHS 2011/65/EU, RED 2014/53/EU
CareMat Ax1T E868, CareMat Bx1T E868, CareMat Cx1T E868, CareMat Mx1T E868
RCL07 radio receiver
Connecting cable,
max. Ø 5mm
LED
Programming key
Battery changing for radio transmitter
6 3
Remove housing cover on rear
(6 countersunk screws M3x5, cross-head size PH1)
When performing a batterychange, ensure that the battery does not
come into contact with the soldered joints of the cables – risk of
short circuit. Locate the battery centrally.
Reinstall housing cover, carefully tighten the 6 screws by hand, do not
overtighten.
8 Disposal
The signal transmitter and its battery are to be disposed of at a suit-
able collecting point, so that the components are recycled, correctly
treated and disposed of in an environmentally correct manner.
The CareMat minus the signal transmitter and battery can be dispo-
sed of as household refuse You can obtain further information on
your local collection point from your refuse collection authority or
from the competent representative.
Signaling protocol
Radio frequency
Working life
Radio range
Type of battery
Type of protection
Ambient temperature
Subject to technical modifications
| Swissdoor ApS, Stenhuggervej 2, 5471 Søndersø, www.swissdoor.dk
TOTMANN
(Pos. 1+2)
EIN/AUS
(Pos. 2+3)
J1
1
IMPULS
(Pos. 4+5)
supply
Versorgungs-
voltage
spannung:
12-24V DC
12-24V DC:
IN1, IN2
IN1, IN2
(Polarity arbitrary)
(Polung beliebig)
consumer
Verbraucher
channel 1:
Kanal 1:
NC, COM, NO
NC, COM, NO
(Wechsler)
Call system
with NO contact
®
ELDAT EasyWave
868.30 MHz
Dependent on application approx. 2 years
up to 30 m in buildings, dependent on structural buil-
ding conditions (up to 100 m in free field)
1x CR2032, 3V Lithium
IP54
0 up to +55° C
J1
1
J1
1
J1
1
Signalling
aerial