Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Important: Read complete instructions before beginning installation.
Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly and plumbing and fittings necessary for
whirlpool operation. An optional drain/overflow kit is available for installation on the bath.
Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do not lift the
bath by the plumbing at any time; handle by the shell only.
Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the finish, do not install the
bath. Damage or defect to the finish claimed after the bath is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's responsibility for
shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims for damage to the carrier. For definitions
of warranty coverage and limitations, refer to the published warranty information packed with the product.
All bath units are factory tested for proper operation and watertight connections prior to shipping. Note: Prior to installation, the bath
must be filled with water and operated to check for leaks that may have resulted from shipping damage or mishandling. Jacuzzi
Whirlpool Bath
©
is not responsible for any defect that could have been discovered, repaired, or avoided by following this inspection and testing
procedure.
RECTANGULAR BATHS
L
(51 mm)
(Heater)
(Motor)
SIDE VIEW
PLUS BATHS WITHOUT INTEGRAL SKIRT
SPECIFICATIONS
(Rectangular)
MODEL
DIMENSIONS
AMIGA™ PLUS
72"
(1829 mm) L
36"
( 914 mm) W
20-3/4" ( 533 mm) H
CETRA
©
536
60"
(1524 mm) L
PLUS
36"
( 914 mm) W
WITH INTEGRAL
21-1/4" ( 553 mm) H
SKIRT
©
SIGNA
5 PLUS
60"
(1524 mm) L
42"
(1067 mm) W
22"
( 559 mm) H
SIGNA
©
6 PLUS
72"
(1829 mm) L
42"
(1067 mm) W
22"
( 559 mm) H
*Add 1/4" to this dimension when roughing-in for 3-wall niche.
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4".
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
TM
RapidHeat
: 120 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 120 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
SPECIFICATIONS
W
2"
H
END VIEW
A
DRAIN/OVERFLOW
DRAIN/OVERFLOW
DIMENSIONS
CUTOUT
*
16-7/8" (429 mm) A
70" x 34"
14"
(356 mm) B
18-1/2" ( 470 mm) A
NA
*
9"
( 229 mm) B
*
17-1/2" (445 mm) A
58" x 40"
12-1/2" (318 mm) B
*
16-7/8" (429 mm) A
70" x 40"
14"
(356 mm) B
L
(Heater)
SIDE VIEW
PLUS BATHS WITH INTEGRAL SKIRT
B
TOTAL WEIGHT/
OPERATING
PRODUCT
FLOOR LOADING
GALLONAGE
WEIGHT
772 lb
50 U.S. gal
105 lb
(351 kg)/
(186 liters)
(48 kg)
43 lb/ft
2
(210 kg/m
2
)
742 lb
48 U.S. gal
92 lb
(337 kg)/
(181 liters)
(42 kg)
2
50 lb/ft
(244 kg/m
2
)
708 lb
42 U.S. gal
108 lb
(321 kg)/
(159 liters)
(49 kg)
40 lb/ft
2
(195 kg/m
2
)
826 lb
55 U.S. gal
118 lb
(375 kg)/
(208 liters)
(54 kg)
39 lb/ft
2
2
(190 kg/m
)
1
(25 mm)
W
1"
H
(Motor)
END VIEW
SKIRT &
HEATER
MOUNTING
Optional,
Factory Installed
U-Frame
(S750000 HEATER KIT)
Integral
Factory Installed
(S750000 HEATER KIT)
Optional,
Factory Installed
U-Frame
(S750000 HEATER KIT)
Not
Factory Installed
Available
(S750000 HEATER KIT)
©
Jacuzzi Whirlpool Bath
BP43000 2/05
Publicidad
Capítulos
Tabla de contenido
