Descripciones de parámetros
8-14 Código de control configurable CTW
Option:
3
3
[6]
PID enable Cuando está activado, habilita el controlador del
8-17 Configurable Alarm and Warningword
El código de alarma y advertencia configurable tiene 16 bits
(0-15). Cada uno de esos bits puede configurarse para cualquiera
de las siguientes opciones.
Option:
[0]
*
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[17]
[19]
[22]
[23]
[24]
[25]
[26]
[27]
[28]
[29]
[30]
[31]
[32]
[34]
[36]
[40]
[41]
[45]
[47]
136
Función:
parámetro 7-40 Reinicio parte I de PID proc..
Disponible solo si parámetro 1-00 Modo Configu-
ración está ajustado como [6] Bobinadora
superf., [7] Vel. lazo a. PID ampl.L o [8] Vel. lazo c.
PID ampl.
PID de proceso ampliado. Equivalente al
parámetro 7-50 PID de proceso PID ampliado.
Disponible solo si parámetro 1-00 Modo Configu-
ración está ajustado como [6] Bobinadora
superf., [7] Vel. lazo a. PID ampl.L o [8] Vel. lazo c.
PID ampl.
Off
10 Volts low warning
Live zero warning
No motor warning
Mains phase loss warning
DC link voltage high warning
DC link voltage low warning
DC overvoltage warning
DC undervoltage warning
Inverter overloaded warning
Motor ETR overtemp warning
Motor thermistor overtemp warning
Torque limit warning
Over current warning
Earth fault warning
Controlword timeout warning
Discharge temp high warning
Hoist mech brake warning
Internal fans warning
External fans warning
Brake resistor short circuit warning
Brake powerlimit warning
Brake chopper short circuit warning
Brake check warning
Heatsink temperature warning
Motor phase U warning
Motor phase V warning
Motor phase W warning
Fieldbus communication warning
Mains failure warning
T27 overload warning
T29 overload warning
Earth fault 2 warning
24V supply low warning
Danfoss A/S © 05/2015 Reservados todos los derechos.
®
VLT
AutomationDrive FC 301/302
8-17 Configurable Alarm and Warningword
El código de alarma y advertencia configurable tiene 16 bits
(0-15). Cada uno de esos bits puede configurarse para cualquiera
de las siguientes opciones.
Option:
[58]
[59]
[60]
[61]
[62]
[64]
[65]
[66]
[68]
[73]
[76]
[77]
[78]
[89]
Función:
[163]
[165]
[10002]
[10004]
[10007]
[10008]
[10009]
[10010]
[10011]
[10012]
[10013]
[10014]
[10016]
[10017]
[10022]
[10026]
[10027]
[10028]
[10029]
[10030]
[10031]
[10032]
[10033]
[10034]
[10036]
[10037]
[10038]
[10039]
[10045]
[10046]
[10047]
[10048]
[10049]
[10060]
[10061]
AMA internal fault warning
Current limit warning
External interlock warning
Feedback error warning
Frequency max warning
Voltage limit warning
Controlboard overtemp warning
Heatsink temp low warning
Safe stop warning
Safe stop autorestart warning
Power unit setup warning
Reduced powermode warning
Tracking error warning
Mech brake sliding warning
ATEX ETR cur limit warning
ATEX ETR freq limit warning
Live zero error alarm
Mains phase loss alarm
DC overvoltage alarm
DC undervoltage alarm
Inverter overload alarm
ETR overtemperature alarm
Thermistor overtemp alarm
Torque limit alarm
Overcurrent alarm
Earth fault alarm
Short circuit alarm
CTW timeout alarm
Hoist brake alarm
Brake powerlimit alarm
Brakechopper shortcircuit alarm
Brake check alarm
Heatsink temp alarm
Phase U missing alarm
Phase V missing alarm
Phase W missing alarm
Inrush fault alarm
Fieldbus com faul alarm
Mains failure alarm
Phase imbalance alarm
Internal fault
Heatsink sensor alarm
Earth fault 2 alarm
Powercard supply alarm
24V supply low alarm
1.8V supply low alarm
Speed limit alarm
Ext interlock alarm
Feedback error alarm
Función:
MG33MK05