Replacing The Battery; Battery Charging; Recommandations Importantes - Peg-Perego Polaris Ranger RZR 900 Instrucciones De Montaje

ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
Do not use the toy if you find it damaged after
opening the packaging. Contact the shop where you
bought it or the customer support centre.
Take care in the presence of children while
assembling the toy, given the risks caused by small
parts (ingestion hazard) and the plastic bags that
contain them (choking hazard).
To assemble the toy, you will need a flat-head
screwdriver, a Phillips screwdriver, a hammer, and a
pair of pliers.
ASSEMBLY
1 • Remove the chassis from the packaging and
position it on its side. Snap fit the teeth of the 2
red supports onto the chassis.
2 • Position the chassis horizontally and screw up
the 4 internal screws while holding the 2
supports in position.
3 • Push the 2 rear cylindrical shock absorbers into
the slots, ensuring that the sides are correct
(right and left are indicated on the back of the
items).
4 • Push the side trim section into the 2 slots in the
chassis. Fit the other trim section on the
opposite side.
5 • Fit the roll-bar support, first engaging the rear
section and then the front. Fit the other side in
the same way.
6 • Fix on the supports with the screws provided.
7 • Place the top of the rollbar. Mantain the holes
represented by the letter A on the front and the
holes represented by the letter B to the rear of
the vehicle.
8 • Fix the roll bar using pressure to engage the 2
self-threading screws, one on each side.
9 • Attach the three plastic rings to rollbar. The
holes position is up and down the back of the
vehicle.
10 • Mount the three fog lights on the roof bars and
attach them with the screws provided (one per
light).
11 • Apply the silver stickers in the 2 rear light seats.
12 • Push the rear lights into the respective seats.
13 • Position the seat as required (the seat can be
fitted in 2 positions) and fix it with the 2 screws
provided. Fit the other seat in the same way.
14 • Insert the 2 seatbelt buckles into the respective
central slots between the seats, as shown in the
figure.
15 • Fit the 2 ring clamps on the roll bar, one on each
side, opening them to position them correctly.
16 • Fix the 2 belts to the respective ring clamps with
the screws provided.
17 • Apply the speedometer sticker and push to fit
the transparent cover. Now fit the speedometer
to the dashboard, inserting first the tongue and
then the tooth.
18 • Snap fit the dashboard cover, inserting first the
upper teeth and then the lower, as shown in the
figure.
19 • Join the two sections of the steering wheel.
20 • Insert the horn into the central hole of the
steering wheel, following the instructions
included in its packaging.
21 • Remove the plastic protector from the steering
shaft. Fit the steering wheel on the steering
column, lining up the respective holes.
22 • On one side insert the screw and on one other
the nut, and fix the steering wheel as shown in
the figure.
23 • Install the two parts of the windshield as shown.
Picture A shows the grille fitted correctly
24 • Secure the grille with the three screws.
25 • Place the windshield on the hood hooking the
three central tabs.
26 • Fit the windscreen of the vehicle with screws.
27 • Snap fit the 2 remaining front shock absorbers,
ensuring that the sides are correct (right and left
are indicated on the back of the items).
28 • Fit the front cover engaging it to the chassis at
the 6 points highlighted in detail A.
29 • Screw on the cover with the 2 screws provided.
30 • Apply the silvered stickers in the 2 front light
seats.
31 • Push the front lights into the respective seats.
32 • Remove the protective caps from the steering
levers. On one side, slide on one of the large
washers provided.
33 • Fit one of the two front wheels (the narrower
ones) on this same side. Keep the wheel trim on
the outside (check that it is fitted onto the
wheel and attach it to its pin if necessary). Next,
insert a small washer and then the nut. Tighten
the nut to secure the wheel. Use the same
procedure to fit the other front wheel.
34 • Remove the protective caps from the rear axle
and insert the axle into the rear of the vehicle as
shown in the figure.
35 • On one of the rear wheels, on the opposite side
to the rim, push on a driver. Now slide the wheel
onto the axle, and keep it in position while fitting
the other rear wheel in the same way.
36 • Fit a small washer and nut on both wheels.
Tighten the nuts using the spanner provided on
one side and a pair of pliers on the other.
37 • Snap fit the 4 wheel hubcaps.
38 • Open the battery compartment by rotating the
red catch to the lock open position. Connect the
electrical system plug with the battery plug.
39 • Close the battery compartment by inserting the
cover at the front below the cover plate.
Complete the operation by inserting the red
catch and rotating it 180º using a coin. The
vehicle is now ready for use.
FEATURES AND INSTRUCTIONS FOR
USE
40 • A: HORN. Press the yellow button to sound the
horn.
B: Passenger HANDRAIL.
C: Electrical accelerator and brake pedal. The
brake activates automatically when the
accelerator is released.
41 • To release the seat belt: 1 pull towards the
centre while pushing the button; 2 disengage.
42 • Rear DRINKS HOLDER. There is a double drinks
holder in the rear box.
43 • ADJUSTABLE SEATS. The seats can be adjusted
in 2 positions as the child grows, as shown in the
figure.
44 • GEAR LEVER: when supplied the vehicle speed is
limited to first gear (1 - see figure). It also has a
reverse (R), and a second gear (2) recommended
only for expert drivers. To enable the second
gear, unscrew the red stop on the gear lever.
45 • Rotate the stop 90°, as shown in the figure, and
fix in position with the screw. Now by pulling
back the gear lever the vehicle can run in second
gear.
46 • ACCESSORY: trailer to attach to the vehicle
(sold separately).

REPLACING THE BATTERY

PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
47 • Use a coin to open the battery compartment.
Disconnect the battery from the system. Remove
the 2 screws from the battery holder in the
compartment.
48 • Replace the flat battery. Put the battery holder
back in place and secure it with the screws.
Connect the two plugs, close the battery
compartment and fasten it shut.

BATTERY CHARGING

WARNING: BATTERY CHARGING AND EVERY
OTHER OPERATION ON THE ELECTRICAL
SYSTEM MUST BE CARRIED OUT BY ADULTS
ONLY.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
49 • Disconnect plug A of the electrical system from
plug B of the battery by pressing laterally.
50 • Connect the battery charger to a domestic
power outlet according to the instructions
included with the charger. Connect plug B with
plug C of the battery charger.
51 • When charging is complete, disconnect the
battery charger from the power outlet and then
disconnect plug C from plug B.
52 • Fully insert plug B into plug A, until it snaps into
position. At the end of charging operations
always remember to insert and fix the battery
holder. Close the battery compartment and
secure it with the catch.
FRANÇAIS
PEG PEREGO ® vous remercie d'avoir
choisi ce produit. Depuis plus de 60 ans,
PEG PEREGO accompagne les promenades
des enfants. Dès leur naissance, avec les
landaus puis avec les poussettes et plus
tard, avec les jouets à pédales et à
batterie.
Découvrez sur notre site la gamme
complète des produits, les nouveautés et
d'autres renseignements sur le monde Peg
Perego.
www.pegperego.com
Peg Perego S.p.A. est une entreprise disposant
d'un système de management de la qualité certifié
conforme à la norme ISO 9001 par
TÜV Italia Srl. Cette certification garantit aux
clients et aux consommateurs une transparence et
une confiance en l'entreprise et son mode de
fonctionnement.
RECOMMANDATIONS
IMPORTANTES
Lisez attentivement ce manuel d'instructions pour
vous familiariser avec le modèle et apprendre à votre
enfant à le conduire de façon correcte, amusante et
en toute sécurité. Conserver ensuite ce manuel pour
pouvoir vous y référer à l'avenir.
Si le produit est confié à des tiers, assurez-vous qu'il
soit accompagné du manuel d'instructions.
Avant d'utiliser le véhicule pour la première fois,
mettez en charge la batterie pendant 18 heures.
Ne pas appliquer cette règle pourrait être à l'origine
de dommages irréversibles à la batterie.
• Âge 3+
• Poids maximal autorisé 60 kg
• Véhicule à 2 places
• 1 Batterie rechargeable de 12 V 12 Ah scellée au plomb
• 2 roues motrices
• 2 moteurs de 175 W
• Vitesse en première 3,2 km/h
• Vitesse en seconde 6,5 km/h
• Vitesse en marche arrière 3,2 km/h
Ne pas dépasser le poids maximal autorisé de 60 kg.
Cette limite s'applique aussi bien aux conducteurs
qu'à l'éventuel chargement.
Peg Perego se réserve le droit d'apporter, à tout
moment, des modifications aux modèles et aux
données figurant dans ce livret, pour des raisons de
caractère technique ou de management.