RIB DUKE 24V 110 Manual Del Usuario página 32

G
B
J1 N F Power supply 230 Vac 60/50 Hz - external to the control panel
- (120V/60Hz upon request)
J2 COM. Common contact
CLOSE Closing impulse contact (NA)
OPEN Opening impulse contact (NA)
STOP STOP impulse contact (NC)
AERIAL Radio Antenna
SIGNAL Gate open state and battery state output indicator (24Vdc 3W
max)
J3 A+TEST + 24Vdc safety strip self-test power supply
EDGE N.C. Safety strip contact (NC)
COM. Common contact
PHOTO N.C. Photocells contact (NC)
K BUTT. Single pulse contact (NO)
PED. BUTT. Pedestrian opening contact (NA)
A+ + 24Vdc accessories power supply
A - - 24Vdc accessories power supply
LOCK Electric lock connection (MAX 15W 12V)
- 24Vdc blinker (code ACG7061) power supply. Pay attention
to the polarity.
J4 SECONDARY Connection to secondary coil of transformer 18 Vac
TRANSFORMER
J5 MOTOR 1 MOTOR 1 CONNECTION (without polarity)
J6 MOTOR 2 MOTOR 2 CONNECTION (without polarity)
J7 Connector dedicated to the factory programming. DO NOT
REMOVE ANY JUMPER! OTHERWISE THE OPERATOR WILL
NOT WORK!
SW T24 2V
J8 Connector dedicated to the factory programming (only CRX
control board) DO NOT REMOVE ANY JUMPER! OTHERWISE
THE OPERATOR WILL NOT WORK!
SW RADIO
J9 RADIO Built-in radio module (model CRX), or connector for radio
receiver RIB, 24 Vdc supply
J10 BATTERY Connector for charge card of 24Vdc battery (code ACG4648)
CHARGER
TR1 TRIMMER RUN Trimmer for high speed adjustment operations
TR2 TRIMMER LOW Trimmer for low speed adjustment operations
SPEED
TR3 TRIMMER TCA Trimmer for automatic closing time adjustment (DISABLED
DEFAULT AND DL6 LED OFF)
S3 PROG Programming button
B - SETTINGS
DIP 1 (ON) - MOTOR ROTATION DIRECTION CONTROL (POINT C)
DIP 2 (ON) - TIMER (POINT D)
DIP 3 (ON) - ACTIVATES DOOR RELEASE DURING PHASES OF SLOWDOWN AND
TOTAL OPENING AND CLOSING (AS PER THE IMPACT TESTS OF EN12453)
DIP 1-2 MEMORIZATION/CANCELLATION OF RADIO CONTROL CODES FOR TOTAL
OPENING (ONLY MODEL CRX) (POINT E)
DIP 1-3 MEMORIZATION/CANCELLATION OF RADIO CONTROL CODES FOR
PEDESTRIAN OPENING (ONLY MODEL CRX) (POINT F)
DIP 2-1 MICRO-SWITCH CONTROLLER FOR PEDESTRIAN OPENING TIMER
DIP 4 Photocells always active (OFF) - Photocells active only during closing (ON)
DIP 5
Pre-blinking (ON) - Normal blinking (OFF)
DIP 6 Single pulse command (K BUTT) and step-by-step radio receiver (OFF) - automatic
(ON)
DIP 7
Power sensor operation (ON-activated) time operation (OFF-activated).
DIP 8 Electric lock activation (ON-activated)
DIP 9 Electric lock pulse release (ON-activated)
DIP 10 Electric lock pulse engagement (ON-activated)
DIP 11 Easy release activation (ON-activated)
DIP 12 Sensor TEST activation (ON-activated).
DIP 13 Selection of 1 or 2 motor operation (default OFF 2 motors)
DIP 14 Selecting sensitivity to the impact
A - CONTROL PANEL FEATURES
J2
J9
J10
J8
J7
S3
FUSE 1 T 8 A Motor protection fuse
F1 T 2 A Transformer protection fuse
BRIDGE Connecting bridge rectifier
DIP 15 Selecting sensitivity to the impact
DIP 14 DIP 15 Selecting sensitivity to the impact
OFF OFF HIGH (maximum protection)
ON OFF MEDIUM HIGH
OFF ON MEDIUM LOW
ON ON LOW (suggested in case of wind)
DIP 16 IMMEDIATE CLOSING AFTER PASSING IN FRONT OF PHOTOCELLS
ON ACTIVATED
OFF DEACTIVATED
JP1 => Check that the jumper is inserted!
JP2 => Check that the jumper is inserted!
JP3 => Check that the jumper is inserted!
PROG => S3 Programming button
ADJUSTMENTS
ATTENTION: PUT DIP 3 IN THE ON MODE ONLY AFTER HAVING CARRIED OUT ALL THE
PROGRAMMING PROCEDURES.
NOTE: WITH DIP 3 (ON) BRIEF GATE REVERSAL AFTER IMPACT IS ACTIVATED.
THIS BRIEF GATE REVERSAL PERMITS STATIC FORCE TO BE REDUCED TO ZERO
32
J1 F1
J3 TRANSFORMER
J4
FUSE
1
BRIDGE
J5
J6
TR3
TR1 TR2