Personal Safety; Electrical Safety - Skil 0780 Manual Original

- do not over reach and do not cut above shoulder
height (this helps prevent unintended tip contact
and enables better control of the chain saw in
unexpected situations)
- only use replacement bars and chains specified
by the manufacturer (incorrect replacement bars
and chains may cause chain breakage and/
or kickback)
- follow the manufacturer's sharpening and
maintenance instructions for the saw chain
(decreasing the depth gauge height can lead to
increased kickback)

PERSONAL SAFETY

• It is recommended that the first time user should have
practical instruction in the use of the chainsaw and the
protective equipment from an experienced operator and
that the initial practice should be cutting logs on a saw
horse or cradle
• Do not touch rotating chain
• Do not operate chain saw near other people,
children or animals
• Do not operate chain saw after drinking alcohol
or under the influence of intoxicating drugs
or medication
• This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the tool by a person responsible
for their safety
• Ensure that children do not play with the tool

ELECTRICAL SAFETY

• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
• Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• Only use an extension cord which is intended for
outdoor use and equipped with a watertight plug
and coupling-socket
• Only use extension cords with a maximum length of
20 metres (1,5 mm²) or 50 metres (2,5 mm²)
• Always switch off tool and disconnect plug from power
source if the power supply cord or the extension cord is
cut, damaged or entangled (do not touch the cord
before disconnecting the plug)
• Protect the (extension) cord from heat, oil and
sharp edges
• Never use the cord for carrying, pulling or unplugging
the tool
• Inspect the cord periodically and have it replaced by
a qualified person, if damaged
• Inspect the extension cord periodically and replace it,
if damaged (inadequate extension cords can
be dangerous)
• Do not use the tool if the switch does not turn it on and
off; always have a damaged switch repaired by a
qualified person
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Always switch off tool and disconnect plug from power
source if the power supply cord or the extension cord is
cut, damaged or entangled (do not touch the cord before
disconnecting the plug)
5 Do not expose tool to rain
6 Wear protective glasses and hearing protection
7 Double insulation (no earth wire required)
8 Do not dispose of the tool together with household
waste material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of this tool,
it must be disposed of safely and not left unattended
USE
• Assembly 9
! do not connect the chain saw to mains before
it is completely assembled
! always use gloves when handling the chain
- place the chain saw on any suitable flat surface
- remove cover plate A by turning locking knob
B counter-clockwise
- slide chain C in the slot around chain bar D
! ensure chain is in correct running direction by
comparing with chain symbol E
- fit the chain onto drive sprocket F and guide chain
bar D, so that fastening bolt G and the two guide
fins H fit into the keyway of chain bar D, and that
chain tensioning peg J fits into the respective hole
of chain bar D
- if necessary, turn tensioning knob K to bring tensioning
peg J in alignment with the hole in chain bar D
- check if all parts are seated properly and hold chain
and chain bar in a level position
- turn tensioning knob K until all the slack is taken up in
the chain
- mount cover plate A as illustrated
- tighten locking knob B on fastening bolt G by turning
it clockwise
• Tensioning chain 0
- place the chain saw on any suitable flat surface
- check if the chain links are correctly located in the slot
around chain bar D
1) loosen locking knob B until it is just holding chain bar
in position (do not remove)
2) lift the chain bar somewhat and hold it in that position
3) turn chain tensioning knob K upwards until the lowest
chain links come up and JUST touch the bottom of
chain bar D
4) tighten locking knob B by turning it clockwise
5) release chain bar
6) the correct chain tension is reached when the chain can
be raised approx. 4 mm from the chain bar in the centre
! always check the chain tension before use, after
the first cuts and regularly during use (approx.
every 10 minutes)
- upon initial operation, new chains can
lengthen considerably
11