Description Of Symbols; General Power Tool Safety Warnings - Silverline 128965 Manual De Usario

GB

Description of Symbols

The rating plate on your tool may show symbols. These represent
important information about the product or instructions on its use.
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction Manual
Double insulated for additional protection
Conforms to relevant legislation and safety standards
Environmental Protection
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for
recycling advice
Specification
Voltage: ................................................230V~
Frequency: ...........................................50Hz
Power: ..................................................950W
No load speed: .....................................120-380m/min
Belt size: ..............................................76 x 533mm
Weighted vibration: ..............................2.316m/s²
Uncertainty: ..........................................1.5m/s
Sound pressure: ...................................92.3dB(A)
Sound power: .......................................103.3dB(A)
Uncertainty: ..........................................3dB(A)
Protection class: ...................................
The sound intensity level for the operator may exceed
85dB(A) and sound protection measures are necessar
As part of our ongoing product development, specifications
of Silverline products may alter without notice
Carefully read and understand this manual and any label attached to
the tool before use. Keep these instructions with the product for future
reference. Ensure all persons who use this product are fully acquainted
with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk
factors. Use with caution. If you are at all unsure of the correct and safe
manner in which to use this tool, do not attempt to use it.
4
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
Work Area Safety
a) Keep work area clean and well lit. Cluttered or dark areas invite
b) Do not operate power tools in explosive atmospheres, such as
c) Keep children and bystanders away while operating a power tool.
Electrical Safety
a) Power tool plugs must match the outlet. Never modify the plug in
b) Avoid body contact with earthed or grounded surfaces, such as
c) Do not expose power tools to rain or wet conditions. Water
d) Do not abuse the cord. Never use the cord for carrying, pulling or
e) When operating a power tool outdoors, use an extension cord
f) If operating a power tool in a damp location is unavoidable, use
2
Personal Safety
a) Stay alert, watch what you are doing and use common sense
b) Use personal protective equipment. Always wear eye protection.
c) Prevent unintentional starting. Ensure the switch is in the
d) Remove any adjusting key or wrench before turning the power
e) Do not overreach. Keep proper footing and balance at all times.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your
accidents
in the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes
Distractions can cause you to lose control
any way. Do not use any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching outlets will reduce risk
of electric shock
pipes, radiators, ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or grounded
entering a power tool will increase the risk of electric shock
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the
risk of electric shock
suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock
a residual current device (RCD) protected supply. Use of an RCD
reduces the risk of electric shock
NOTE: The term "residual current device (RCD)" may be replaced by
the term "ground fault circuit interrupter (GFCI)" or "earth leakage
circuit breaker (ELCB)".
when operating a power tool. Do not use a power tool while you
are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in
serious personal injury
Protective equipment such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate conditions will reduce
personal injuries
off-position before connecting to power source and/or battery
pack, picking up or carrying the tool. Carrying power tools with your
finger on the switch or energising power tools that have the switch on
invites accidents
tool on. A wrench or a key left attached to a rotating part of the power
tool may result in personal injury
This enables better control of the power tool in unexpected situations
hair, clothing and gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts
g) If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected and properly
used. Use of dust collection can reduce dust-related hazards