Publicidad
Idiomas disponibles
Idiomas disponibles
English
Application
The compact audio set for 1 - 4
residential units. Encompasses the
door station for surface mounting,
transformer for distributor mounting
and in-house telephones for surface
mounting. With the basic functions
calling, speech and door release.
Illuminated information panel.
Electrical voltage
Mounting, installation and servicing
work on electrical devices may only
be performed by a suitably qualified
electrician. Failure to observe this
regulation could result in the risk of
serious damage to health or fatal
injury due to electric shocks.
• Ensure maximum fusing of 16A for
the mains connection in the building
installation.
• For surface mounting, ensure that
"protection against direct contact"
with active parts is provided. For
details, consult VDE 0100/DIN 57100
part 410.
Electrostatic charging
As a result of electrostatic charging,
direct contact with the circuit board
can result in destruction of the
device. Direct contact with the circuit
board must therefore be avoided.
Scope of supply SET CA 812-1
• Door station CA 812-1
• Siedle screwdriver
• In-house telephone HTS 811-...
• Transformer TR 603-...
• This product information
Scope of supply SET CA 812-2 as
described above but
• door station CA 812-2
• 2 in-house telephones HTS 811-...
4
Scope of supply SET CA 812-3 as
described above but
• Door station CA 812-4
• 3 in-house telephones HTS 811-...
Scope of supply SET CA 812-4 as
described above but
• Door station CA 812-4
• 4 in-house telephones HTS 811-...
Scope of supply SET CA 812-11
• Door station CA 812-1
• Siedle screwdriver
• In-house telephone HTS 811-...
• Transformer TRS 711-1 125 V
• This product information
Scope of supply SET CA 812-12 as
SET CA 812-11, but
• Door station CA 812-2
• 2 in-house telephones HTS 811-...
Scope of supply SET CA 812-13 as
SET CA 812-11, but
• Door station CA 812-4
• 3 in-house telephones HTS 811-...
Scope of supply SET CA 812-14 as
SET CA 812-11, but
• Door station CA 812-4
• 4 in-house telephones HTS 811-...
Door station mounting
1 Unscrew the front of the housing.
To do this, release the Siedle screw
on the underneath of the housing.
Hinge the front of the housing
forward.
2 Surface mounting the door sta
tion. Recommended mounting
height appr. 1.50 m /4.9 ft. to centre
device. Please note: The cable is
inserted in the lower area of the
base plate!
3 Strip back the installation cable
close to the wall (appr. 10 mm)
and insert the cores into the base
plate. Fasten the base plate using 4
screws. Close the two openings at
the top using rubber stoppers. Install
in accordance with the terminal
diagram. The cores may only be laid
in the admissible installation space.
4 Depending on the installation
environment, it may be necessary
to change the door station speech
volume in order to permit clear
speech transmission.
5 Hook the front of the housing
onto the base plate at the top and
close. Tighten the screw on the
underneath of the housing.
Transformer mounting
6 Mount the transformer on the top
hat rail (distribution).
7 Surface mounting is possible with
accessory ZAP 30. (not included in
scope of supply)
In-house telephone mounting
Strip back cable to appr. 80 mm.
8 Open the device from the back by
pressing in the locking lever.
9 Recommended mounting height
appr. 1.50 m /4.9 ft. to centre
device.
10 When mounting directly on the
wall, fasten the base plate using
4 screws, paying attention that
the plate is the right way up (top
marking).
11 When mounting on a switch box,
use the screw openings in the centre
of the device, paying attention that
the plate is the right way up (top
marking).
12 Install in accordance with the
terminal diagram. The cores of the
installation cable must be stored
inside the free installation space in
the base plate.
13 Insert the coloured plug of the
spiral cable into the socket at the
housing. A distinct click is audible
when the plug is correctly inserted.
14 Insert the other end of the spiral
cable in the receiver until the plug
clicks audibly into place. This con
nection can no longer be detached.
15 Hook the housing into the base
plate from above and close by
exerting a slight pressure.
Publicidad
