Siemens SITRANS P DS III Serie Istrucciones De Servicio página 142

Anexo
Hart Handterminal
Firmware Rev. F1.6
structure of operation
2 Online 1 (PV meas) *)
2 (PV) status
3 Module type
4 Identification 1 Operation Unit
2 Device
3 Basic Parameters
5 Config Inp/Outp 1 Quick-Setup & Meas.
2 Input
140
*) measurement display
**) M = method
1 Tag
2 Long Tag --> M **)
3 Descriptor
4 Message
5 Date
1 Manufacturer
2 Model
3 Device identification
4 Distributor
5 MLFB Order Number 1 MLFB Order No --> M
6 Measurement type
7 Fabrication-No
8 Final asembly number
9 Sensor serial number
10 Revisions 1 Universal rev.
2 Field device rev.
3 Software rev.
4 Hardware rev.
1 Pressure unit
2 LSL (Lower Sensor Limit)
3 USL (Upper Sensor Limit)
4 Minimum Span
5 LRV (Lower Range Value)
6 URV (Upper Range Value))
7 Pressure damping
8 Pressure xfer function xfer = transfer
1 PV, Current, Status 1 (PV meas) *)
2 AO (analogue output)
3 (PV) % range
4 Status see --->
5 Measurement type
2 Meas.Val. & Status 1 Pressure Values
2 Temperature Values
3 Level, Vol, Mass Values
(shown if valid items)
4 Vol-, Mass- & Flow
(shown if valid items)
5 Appl & Stat
(shown if valid items)
3 Quick-Setup 1 Tag
2 Ext TAG --> M
3 PV is
4 (PV) unit
5 Position correction
6 LRV
7 URV
8 Pressure damping
9 Pressure xfer function
1 Config Pres/Temp 1 Pressure sensor
2 Temperature sensor
3 Pres units see -->
4 Temp units see -->
2 Display Process Variables 1 Prozess variables
3 Meas Switch/Mapper 1 measurement
2 PV is
3 SV is
4 TV is
5 QV is
6 (measurement) config
e.g. Level
6 (measurement) config
e.g. Flow
6 (measurement) config
e.g. Customer
7 Unser linearization
if Level, Flow or Customer
this is valid - otherwise not
4 Meas.Limits & Span 1 Module range
2 Active Device Variables
additional if measurement
is mapped to level
6 Diagnosis/Service
1 Pressure
2 Pres status
3 Untrimmed pressure
4 Untrimmed pres status
1 Sens-Temp
2 Sens-Temp status
3 Electr-Temp
4 Electr-Temp status
1 Level
2 Level status
3 Volume
4 Volume status
5 Mass
6 Mass status
1 Vol-Flow
2 Vol-Flow status
3 Mass-Flow
4 Mass-Flow status
1 Customer
2 Customer Status
1 Position corr --> M
1 Pressure
2 Untrimmed pres
3 Pressure units 1 Pres abs/rel
2 Pressure unit
3 Untrimmed pres unit
1 Sens-Temp
2 Electr-Temp
3 Temp units 1 Sens-Temp unit
2 Electr-Temp unit
1 Pressure sensor
1 Temperature sensor
1 (PV measurement)
2 (PV) %rnge
3 AO
4 (SV measurement)
5 (TV measurement)
6 (QV measurement)
1 Input scaling 1 Pres abs/rel
2 Pressure unit
3 Input LRV
4 Input URV
2 Level scaling 1 Level unit
e.g. Level scaling 2 Level LRV
3 Level URV
3 Volume scaling 1 Volume unit
2 Vol LRV
3 Vol URV
2 Density unit
3 Density
3 Mass unit
1 Input scaling 1 Pres abs/rel
2 Pressure unit
3 Input LRV
4 Input URV
2 Flow scaling 1 Vol flow unit
2 Vol flow LRV
3 Vol flow URV
2 Density unit
3 Density
3 Mass flow unit
1 Input scaling 1 Pres abs/rel
2 Pressure unit
3 Input LRV
4 Input URV
3 Customer scaling 1 Cust unit (5 Ch)
2 Cust LRV
3 Cust URV
1 Special Curve status --> only if meas not pres
2 No curve points
3 Setup special char --> M
4 Display special char --> M
1 Pressure 1 Pressure unit
2 Pres USL
3 Pres LSL
4 Trimpoint sum
5 Pres min.span
2 Sens-Temp 1 Sens-Temp unit
2 Sens-Temp USL
3 Sens-Temp LSL
4 Sens-Temp min.span
3 Electr-Temp 1 Electr-Temp unit
2 Electr-Temp USL
3 Electr-Temp LSL
4 Electr-Temp min.span
4 Untrimmed Pres 1 Untrimmed Pres unit
2 Untrimmed Pres USL
3 Untrimmed Pres LSL
4 Untr Pres min.span
5 Level 1 Level unit
2 Level USL
3 Level LSL
4 Level min.span
SITRANS P, Serie DS III
A5E00053220-05