Ingersoll Rand SS3F2-GM Manual Del Propietario Con La Lista De Piezas página 4

EN
INSTALLING THE AIR INLET FILTER

CAUTION
Do not operate without air inlet filter .
Install the air inlet filter at the inlet connection at the
bare pump . If heavy duty filtration is required, contact
your dealer for information .
INSTALLING DISCHARGE PIPING

If it is necessary to install air discharge piping or condensate
discharge piping, adhere to the following general guidelines.
Contact your dealer for more information.
WARNING
If an aftercooler, check valve, block valve, or any other
restriction is added to the compressor discharge, install
a properly-sized ASME approved safety/relief valve
between the compressor discharge and the restriction .
CAUTION
If you will be using Ingersoll-Rand synthetic
compressor lubricant, all downstream piping material
and system components must be compatible . Refer to
the following material compatibility list . If there are
incompatible materials present in your system, or if
there are materials not included in the list, contact your
dealer .
Suitable:
Viton®, Teflon®, Epoxy (Glass Filled), Oil Resistant Alkyd,
Fluorosilicone, Fluorocarbon, Polysulfide, 2-Component
Urethane, Nylon, Delrin®, Celcon®, High Nitrile Rubber
(Buna N. NBR more than 36% Acrylonitrile), Polyurethane,
Polyethylene, Epichlorohydrin, Polyacrylate, Melamine,
Polypropylene, Baked Phenolics, Epoxy, Modified Alkyds
(® indicates trademark of DuPont Corporation)
Not Recommended:
Neoprene, Natural Rubber, SBR Rubber, Acrylic Paint, Lacquer,
Varnish, Polystyrene, PVC, ABS, Polycarbonate, Cellulose
Acetate, Low Nitrile Rubber (Buna N. NBR less than 36%
Acrylonitrile), EPDM, Ethylene Vinyl Acetate, Latex, EPR,
Acrylics, Phenoxy, Polysulfones, Styrene Acrylonitrile (San),
Butyl
GENERAL REQUIREMENTS-The piping, fittings, receiver tank,
etc. must be certified safe for at least the maximum working
pressure of the unit. Use hard-welded or threaded steel or
copper pipes, cast iron fittings and hoses that are certified
safe for the unit's discharge pressure and temperature. DO
NOT USE PVC PLASTIC. Use pipe thread sealant on all threads,
and make up joints tightly to prevent air leaks.
CONDENSATE DISCHARGE PIPING- If installing a
condensate discharge line, the piping must be at least
one size larger than the connection, as short and direct as
possible, secured tightly and routed to a suitable drain point.
Condensate must be disposed of in accordance with local,
state, and federal laws and regulations.
4
RELEASED 26/Jan/2020 20:37:54 GMT
NOTE: All compressed air systems generate condensate
which accumulates in any drain point (e.g. tanks, filters,
drip legs, aftercoolers, dryers). This condensate contains
lubricating oil and/or substances which may be regulated
and must be disposed of in accordance with local, state, and
federal laws and regulations.

Any electrical installation and service required should
be performed by a qualified electrician who is familiar
with all applicable local, state and federal laws and
regulations .
This product should be connected to a grounded,
metallic, permanent wiring system, or an equipment-
grounding terminal or lead on the product .
GENERAL - The motor rating, as shown on the motor
nameplate, and the power supply must have compatible
voltage, phase and hertz characteristics.
WIRE SIZE - The electrical wiring between the power supply
and electric motor varies according to motor horsepower.
Power leads must be adequately sized to protect against
excessive voltage drop during start up. Information for
selecting the proper wire size and securing connections
should be provided with the motor. If not, refer to the
National Electric Code (NEC) or applicable local, state and
federal laws and regulations. If other electrical equipment is
connected to the same circuit, the total electrical load must
be considered in selecting the proper wire size. DO NOT USE
UNDERSIZE WIRE.
FUSES - Refer to the National Electric Code to determine the
proper fuse or circuit breaker rating required. When selecting
fuses, remember the momentary starting current of an
electric motor is greater than its full load current. Time-delay
or "slow-blow" fuses are recommended.
GROUNDING - The unit is equipped with a power cord
having a grounding wire an an appropriate grounding
plug. The plug must be used with an outlet that has been
installed and grounded in accordance with all local codes and
ordinances. The outlet must have the same configuration as
the plug. DO NOT USE AN ADAPTER.
In the event of a short circuit, grounding reduces the
risk of shock by providing an escape for the electric
current . The unit must be properly grounded .
Improper installation of the grounding plug result in
a risk of electric shock . If repair or replacement of the
cord or plug is necessary, do not connect the grounding
wire to either flat blade terminal . The wire with
insulation having an outer surface that is green with or
without yellow stripes is the grounding wire .
ELECTRICAL WIRING & GROUNDING
WARNING
NOTICE
WARNING
DANGER
22204861 Rev. C