Using The Wall-Mounted Door Control - Chamberlain Whisper Drive Security+ Manual Del Propietário

Using the Wall-Mounted Door Control

THE SMART CONTROL PANEL
Press the push button
to open or close the
door. Press again
to reverse the door
during the closing
cycle or to stop
the door while it's
opening.
This door control
contains a motion
detector that will automatically turn on the light when it
detects a person entering the garage. This feature can be
easily turned off for extended work light use.
Light Feature
Press the Light button to turn the opener light
on or off. It will not control the opener lights
when the door is in motion. If you turn it on and then
activate the opener, the light will remain on for 4-1/2
minutes. Press again to turn it off sooner. The 4-1/2
minute interval can be changed to 1-1/2, 2-1/2 or 3-1/2
minutes as follows: Press and hold the Lock button until
the light blinks (about 10 seconds). A single blink indicates
that the timer is reset to 1-1/2 minutes. Repeat the
procedure and the light will blink twice, resetting the timer
to 2-1/2 minutes. Repeat again for a 3-1/2 minute interval,
etc., up to a maximum of four blinks and 4-1/2 minutes.
When using the opener lights as working lights, we
recommend that you fi rst disable the motion sensor.
Lock Feature
Designed to prevent operation of the door from
hand-held remote controls. However, the door
will open and close from the Door Control, the Outside
Keylock and the Keyless Entry Accessories.
To activate, press and hold the Lock button for 2 seconds.
The Smart Control Panel
message: "LOCK MODE REMOTE CONTROL LOCKED OUT
PRESS LOCK BUTTON TO ENABLE REMOTE."
To turn off, press and hold the Lock button again for
2 seconds. The Lock feature will also turn off whenever the
"learn" button is activated.
Motion Detecting Light Feature
The opener light will turn on automatically when a person
walks in front of the wall-mounted door control. This
feature works by detecting motion and body heat and
may not work in temperatures around 100˚ F (37.7˚ C).
The opener light will come on for 5 minutes, then shut off
automatically if no additional motion or heat differential is
calculated.
To disable this feature, press the Motion Detecting Light
On/Off button on the left side of the door control.
We recommend that you disable the motion
sensor when using the opener lights as working
lights. Otherwise, they will turn off automatically
if you are working beyond the sensor's range.
®
Motion Sensing
ON/OFF
Prog
<LEARN>
Hour
Minute
Language
Degrees (F/C)
Lock Button
® will display the following
(Prog) Learn Feature
The door control is equipped with a Prog <LEARN> button
to assist in learning remote controls to the unit. Press
the Prog <LEARN> button once to initiate LEARN mode
Push and the display will show 'Learn Remote Control - Press
Bar
Learn Button Again to Confi rm'. Press the Prog <LEARN>
button a second time and the display will show 'Learn
Mode - Press Remote Control Button to Learn Remote.'
Press the button of the remote control to be learned and
the work light will blink to confi rm the remote control has
Light
been learned.
Button
(Lang) Language Feature
Press this side button to toggle between the three
languages - English, Spanish, and French.
Degrees F/C Feature
Press this side button to toggle the temperature
units between Fahrenheit and Celsius.
Additional feature when used with the 3-Button
hand-held remote
To control the opener lights:
In addition to operating the door, you may program the
remote to operate the lights.
1. With the door closed, press and hold a
small remote button that you want to
control the light.
2. Press and hold the Light button on the
door control.
3. While holding the Light button, press and hold the Lock
button on the door control.
4. After the opener lights fl ash, release all buttons.
31
Hour & Minute Feature
Press or hold either of these side buttons
to increment the hour or minute displayed
on the LCD display.