Symbols Used; In The Documentation; Warning Notices - Structure And Meaning; Symbols In This Documentation - Bosch KTS 5 Serie Manual Original

en 16 | KTS 530 / 540 / 570 (KTS 5 Series) | Symbols used
1.

Symbols used

1.1

In the documentation

1.1.1 Warning notices -
Structure and meaning
Warning notices warn of dangers to the user or people
in the vicinity. Warning notices also indicate the con-
sequences of the hazard as well as preventive action.
Warning notices have the following structure:
KEY WORD – Nature and source of hazard!
Warning
symbol
Consequences of hazard in the event of fail-
ure to observe action and information given.
¶
Hazard prevention action and information.
The key word indicates the likelihood of occurrence and
the severity of the hazard in the event of non-obser-
vance:
Key word Probability of
occurrence
DANGER Immediate impend-
ing danger
WARNING Possible impending
danger
CAUTION Possible dangerous
situation
1.1.2

Symbols in this documentation

Symbol Designation Explanation
Attention Warns about possible property damage.
!
Information Practical hints and other
i
useful information.
1. Multi-step Instruction consisting of several steps.
2. operation
One-step Instruction consisting of one step.
e
operation
Intermediate An instruction produces a visible inter-

result mediate result.
Final result There is a visible final result on com-
"
pletion of the instruction.
1.2

On the product

!
Observe all warning notices on products and ensure
they remain legible.
Disposal
Dispose of used electrical and electronic
devices, including cables, accessories and
batteries, separately from household waste.
|
1 689 979 987 2015-09-22
Severity of danger if in-
structions not observed
Death or severe injury
Death or severe injury
Minor injury
2.

User information

2.1

Important notes

Important information on copyright, liability and warran-
ty provisions, as well as on equipment users and com-
pany obligations, can be found in the separate manual
"Important notes on and safety instructions for Bosch
Test Equipment". These instructions must be carefully
studied prior to start-up, connection and operation of
the KTS 530 / 540 / 570 (KTS 5 Series) and must always
be heeded.
2.2

Safety instructions

All the pertinent safety instructions can be found
in the separate manual "Important notes on and
safety instructions for Bosch Test Equipment".
These instructions must be carefully studied pri-
or to start-up, connection and operation of the
KTS 530 / 540 / 570 (KTS 5 Series) and must always be
heeded.
2.3

Electromagnetic compatibility (EMC)

The KTS 530 / 540 / 570 (KTS 5 Series) satisfies the
requirements of the EMC directive 2004/108/EG.
i
The KTS 530 / 540 / 570 (KTS 5 Series) is a class
A product as defined by EN 61326-1:2006. The
KTS 530 / 540 / 570 (KTS 5 Series) may cause
high-frequency household interference (radio inter-
ference) so that interference suppression may be
necessary. In such cases the user may be required to
take the appropriate action.
2.4 R&TTE Directive
The KTS 530 / 540 / 570 (KTS 5 Series) is a
class 2 wireless device (R&TTE 1999/55/EC) ap-
proved for use in Europe. In France, use of the
KTS 530 / 540 / 570 (KTS 5 Series) is only permissible
indoors.
i
In non-European countries the corresponding nation-
al regulations on the operation of wireless devices
in the 2.4 GHz frequency band must be heeded (e.g.
WLAN or Bluetooth).
2.5

Measuring category according to

EN 61010-2-030:2010
EN 61010-1:2010 specifies the general safety require-
ments for electrical testers and measuring devices and
defines the measuring categories from 0 to IV in the
section EN 61010-2-030:2010.
The KTS 530 / 540 / 570 (KTS 5 Series) is intended for
use in measuring category 0, i.e. for measurements in
circuits with no direct connection to the mains voltage.
Robert Bosch GmbH