Peavey IPR2 2000 Manual Del Operador página 105

Rated Watts 2ch x 2 ohms
Rated Watts 2ch x 4 ohms
Rated Watts 2ch x 8 ohms
Minimum Load Impedance
Maximum RMS Voltage Swing
Frequency Response
20Hz - 20kHz 2ch x 2 ohms
20Hz - 20kHz 2ch x 4 ohms
20Hz - 20kHz 2ch x 8 ohms
Input CMRR
Voltage Gain
Crossover
Crosstalk
Hum and Noise
Slew Rate
Damping Factor (8 ohms)
Input Sensitivity
Input Impedance
Current Draw @ 1/8 power in VA (watts) 540 (315) @ 2 ohms, 370 (185) @ 4 ohms, 240 (115) @ 8 ohms.
Current Draw @ 1/3 power in VA (watts) 1250 (760) @ 2 ohms, 750 (425) @ 4 ohms, 460 (240) @ 8 ohms.
Idle Consumption
Cooling
Controls
Indicator LEDs
Protection
Connectors
Construction
Dimensions
Net Weight
Gross Weight
Rated power readings made with BW: 20 Hz to 22 kHz. All power measurements made @ 120 VAC or 240VAC.
2 ohm steady state sine wave power is time limited by circuit breaker
*Net Weight does not include power cord.
IPR2 2000 Specification Sheet
™
1100 watts 20ms repetitive burst / 900 watts 1% THD both channels driven @ 1kHz.
600 watts 20ms repetitive burst / 570 watts 1% THD / 530 watts 0.15% THD, both channels driven @ 1kHz.
370 watts 20ms repetitive burst / 325 watts 1% THD / 300 watts 0.15% THD, both channels driven @ 1kHz.
2 ohms
55volts
10Hz - 30kHz; +/- 3 dB at 1 watt, eight ohms.
<0.25% @ 650 watts 20Hz to 4kHz, decreasing to 530 watts @ 20kHz, both channels driven.
<0.15% @ 470 watts 20Hz to 10kHz, both channels driven.
<0.15% @ 260 watts 20Hz to 10kHz, both channels driven.
> - 69 dB @ 1 kHz.
x 60 (+35 dB)
100Hz switchable 2nd order high pass and 3rd low pass per channel.
> -70dB @ 1kHz @ 250 watts power @ 8 ohms.
> -105 dB, "A" weighted referenced to rated power @ 4 ohms.
> 12V/μs
> 170:1 @ 20Hz - 1kHz @ 8 ohms.
.775 volts +/- 3% for 1kHz 4 ohm rated power, .68 volts +/- 3% for 1kHz 2 ohm rated power.
15k ohms, balanced and 7.5k ohms unbalanced.
90VA, 40watts.
Temperature dependent variable speed 80 mm DC fan.
2 front panel attenuators, crossover select switch for HPF, Normal and LPF
Five LED indicators per channel: Active, Signal, DDT
Thermal, DC, subsonic, incorrect loads, under and over voltage.
Inputs: Dual Combination 1/4" & XLR, Outputs: Dual 1/4" signal patch, dual twist lock connectors.
0.062" thick aluminum
3.5"x19"x 10.5" behind front panel + 0.6" for handle
3.23 kg (7.12 lbs.*)
4.31 kg (9.5 lbs.)
, Temperature and DC
™