Menu Settings; Language; Maintenance; Program Beverages - DeLonghi ECAM35075 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

The message "Turning off underway Please wait" appears
on the display (B1), then the appliance performs a rinse
cycle and goes off (standby).
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket:
first turn the appliance off by pressing the
(fig. 6);
press the main switch (A22) (fig. 2).
Important!
Never press the main switch while the appliance is on.

7. MENU SETTINGS

This menu has the following options, each explained in detail
in this section.

Language;

Maintenance:

- Descale,
- Install filter,
- (if a filter has been installed): Replace filter,
- (if a filter has been installed): Remove filter;
Prg. beverages;
Prg. my beverages;

General:

- Set temperature,
- Water hardness,
- Auto-off,
- Energy saving,
- Beep,
- Default beverages,
- Default values;
Statistics.
7.1 Language
To modify the language of the display (B1), proceed as follows:
1. Press
(B6) to enter the "Settings" menu;
2. Press OK (B3) to select "Language". The available languag-
es are displayed;
3. Press the selection arrows (B2 and B4) until the required
language is displayed between the two lines;
4. Press OK to confirm;
5. The appliance goes back to the "Settings" menu;
6. Press
/ESC (B5) to exit the menu.
7.2 Maintenance
Here you can find all the maintenance operations required by
the appliance over time:
Descale: For instructions on descaling, see section "15.
Descaling".
Install filter: For instructions on how to install the filter
(C4), see section "17.1 Installing the filter".
To select the operation you require, proceed as follows:
1. Press
2. Press the selection arrows (B2 and B4) until "Maintenance"
is displayed between the two lines;
3. Press OK (B3) to confirm;
4. Press the selection arrows to display the operation to be
performed;
button
5. Press OK to confirm and perform the operations as de-
scribed in the corresponding sections.

7.3 Program beverages

The appliance is set by default to automatically deliver standard
quantities. To change these quantities and customise the direct-
ly selected beverages and the
follows:
1. Press
2. Press the selection arrows (B2 and B4) until "Prg. beverag-
es" is displayed between the two lines;
3. Press OK (B3) to confirm: the appliance lists the beverages
you can customise;
4. Press the selection arrows until the beverage you want to
customise is displayed, then press OK to confirm;
5. Beverages with coffee: "Program aroma" appears on
the display: press the selection arrows (B2 and B4) or
(B7) until the required aroma is selected (see section "9.4
Temporarily varying the coffee aroma"), then press OK.
"Program coffee" appears on the display together with a
bar which gradually fills as delivery progresses. When the
required quantity is reached, press OK;
Cappuccinos and milk-based recipes: after selecting
the aroma, "Program milk" appears on the display togeth-
er with a bar which gradually fills as milk delivery pro-
gresses. When the required quantity is reached, press OK.
The appliance then makes the coffee. Press OK to interrupt
delivery when the required quantity of coffee is reached.
Hot water: press OK. Delivery begins: press OK when the
required quantity is reached.
6. "Save parameters?": to save the settings, press OK (other-
wise press /ESC - B2 or B5).

7.4 Program My beverages

To customize recipes under the My Menu, follow the procedures
described in previous section " "7.3 Program beverages" by se-
lecting "Prg. my beverages" OR by programing directly under
the My Menu by following instructions described in section "12.
Programming and selecting".
7.5 General
Here you can find the settings to customise the basic functions
of the appliance:
1. Press
9
(B6) to enter the "Settings" menu;
(B6) to enter the "Settings" menu;
(B6) to enter the "Settings" menu;
(B14), proceed as

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido