Statistics; Rinsing - DeLonghi ECAM35075 Manual De Instrucciones

2. Press the selection arrows (B2 and B4) until "General" is
displayed between the two lines;
3. Press OK (B3) to confirm and select the required item with
the selection arrows. Then follow the instructions for each
setting.
• Set temperature:
To modify the temperature of the water used to make the coffee,
proceed as follows:
4. Press OK (B3). The current value appears on the display
(B1) and the "New" value flashes;
5. Select the new value you want to set using the selection
arrows (B2 or B4);
6. When the required value (low, medium, high, maximum)
has been selected, press OK.
The display goes back to the previous screen.
• Water hardness:
For instructions on identifying and setting water hardness, see
section "16. Setting water hardness".
• Auto-off (standby):
Auto-off can be set so that the appliance goes off after 15 or 30
minutes, or 1, 2 or 3 hours
4. Press OK. The current value appears on the display (B1) and
the "New" value flashes;
5. Select the new value you want to set using the selection
arrows (B2 or B4);
6. When the required value (low, medium, high, maximum)
has been selected, press OK.
The display goes back to the previous screen.
• Energy saving:
Use this function to enable or disable energy saving. When ena-
bled, the function reduces energy consumption.
To disable or enable "Energy Saving", proceed as follows:
4. Press OK. The current state ("Enabled" or "Disabled") and
the operation to be performed ("Disable?" or "Enable?") is
displayed. Press OK to confirm;
5. Press OK to disable or enable the function.
The display goes back to the previous screen.
Please note!
• when the function is enabled, the symbol "ECO" appears
on the display.
• When in energy saving mode, a few seconds elapse before
the first coffee, cappuccino or milk-based coffee is deliv-
ered as the appliance must heat up again.
• If the milk container (D) is inserted, "Energy Saving" can-
not be activated.
• Beep:
Use this function to enable or disable the beep. Proceed as
follows:
4. Press OK. The current state ("Enabled" or "Disabled") and
the operation to be performed ("Disable?" or "Enable?") is
displayed. Press OK to confirm;
5. Press OK to disable or enable the function.
The display goes back to the previous screen.
• Default beverages:
Use this function to reset the default values for all the beverag-
es, or the individual beverages programmed previously. Select
the beverage, then proceed as follows:
4. Select "All" to reset the aroma and quantity settings to the
default values, or select the required beverage, then press OK;
5. The machine will display "Reset?". To confirm, press OK;
6. The machine will now display "Reset complete" and goes
back to previous screen.
To reset another beverage, repeat from point 4 or to exit, press
/ESC (B5).
• Default values:
Use this function to reset all settings of the machine to factory
values, keeping only the language option in use.
To proceed with the reset, select Default values from the General
menu (section "7.5 General"):
4. The "Reset" message will display". Press OK;
5. The machine will confirm displaying "Reset complete" and
it goes back to previous screen.
To exit, press /ESC (B5).

7.6 Statistics

This displays statistics relating to the machine. To display the
statistics, proceed as follows:
1. Press (B6) to enter the "Settings" menu;
2. Press the selection arrows (B2 and B4) until "Statistics" is
displayed between the two lines;
3. Press OK (B3): statistics on the appliance are displayed, use
the selection arrows to scroll through the items;
4. Press /ESC (B5) to exit.
To go back to the main screen, press /ESC.

8. RINSING

Use this function to deliver hot water from the coffee spouts
(A9) and hot water spout (C6), if inserted, to clean and heat the
appliance's internal circuit.
Place a container with a minimum capacity of 3.38 floz/100ml
under the coffee and hot water spouts.
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
1) To enable this function, press
on the display (B1);
10
(B5). "RINSING" appears