Publicidad
Idiomas disponibles
Idiomas disponibles
®
LCD Colour Monitor
GB
Please read these operating instructions carefully prior
to operating the unit and keep them for later use.
1 Operating Elements
1.1 Monitor (figs. 1 and 2)
1 IR sensor for control via the remote control
2 Stand-by indication
3 Button MIR to switch over the monitor to mirror-
inverted picture display
4 Button SELECT to successively call the adjusting
scales BRIGHT, COLOR, CONTRAST, TINT (only
for NTSC video sources), and VOLUME
5 Buttons V+ and V-
– to adjust the parameters in the adjusting scales
called with the button SELECT (4)
– to adjust the volume
6 Button
for switching the unit on/off
1.2 Remote control (fig. 3)
The buttons MIR (3), SELECT (4), and V-/V+ (5) cor-
respond to the buttons on the monitor.
7 Button
to change between "monitor switched on"
and "monitor set to stand-by"
8 Button
for muting the speaker
9 Button V1/V2 for switching over between the two
video inputs
10 Button P.P for switching over between different
picture adjustments
11 Button SLEEP for activating the mode "automatic
switching over to stand-by"
Note: The button MODE is without function.
2 Safety Notes
The units (monitor and power supply unit) correspond
to all required directives of the EU and are therefore
marked with
.
WARNING
The power supply unit is supplied with
hazardous mains voltage. Leave servic-
ing to skilled personnel only. Inexpert
handling of the unit may cause an elec-
tric shock hazard.
It is essential to observe the following items:
The units are suitable for indoor use only. Protect
them against dripping water and splash water, high
air humidity, and heat (admissible ambient tempera-
ture range 0 – 40 °C).
Do not set the monitor into operation, or immediately
disconnect the power supply unit from the mains
socket if
1. there is visible damage to the units,
2. a defect might have occurred after a drop or simi-
lar accident,
3. malfunctions occur.
The units must in any case be repaired by skilled
personnel.
For cleaning only use a dry, soft cloth, by no means
chemicals or water.
No guarantee claims for the units and no liability for
any resulting personal damage or material damage
will be accepted if the units are used for other pur-
poses than originally intended, if they are not correctly
installed, operated, or not repaired in an expert way.
If the units are to be put out of operation
definitively, take them to a local recycling plant
for a disposal which is not harmful to the
environment.
Do not put exhausted batteries into the household
rubbish but take them to a special waste disposal
(e. g. collective container at your retailer).
®
Copyright
TVLCD-566COL
3 Applications
The LCD colour monitor in TFT active matrix technol-
ogy is equipped with two video inputs and an audio
input and offers a sharp, high-contrast, and fast picture
display. The picture can be mirror-inverted vertically
and/or horizontally. For audio reproduction a small
speaker has been integrated.
The monitor is suitable for universal use, e. g. in
video surveillance systems or for multimedia applica-
tions. The unit is supplied with a support including
mounting screws, a plug-in power supply unit, and an IR
remote control.
4 Installation
1) Tightly screw the supplied support to the monitor:
Either use the threaded jack (A) at the lower side of
the monitor or the nut (B) which can be moved in the
guide rail.
2) For setting up the support on a surface it can tightly
be mounted with the three supplied screws or be
glued on by removing the foil on its lower side.
For wall or ceiling mounting tightly screw the sup-
port with the three screws.
3) Release the lateral setscrew at the support, adjust
the desired monitor inclination, and retighten the set-
screw.
4) Connect the mini DIN plug of the supplied cable to
the inline jack (C) of the monitor cable.
5) It is possible to connect two video sources (cameras,
DVD players, etc.): Connect the yellow phono plug
to the video output of the 1
phono plug to the video output of the 2
source.
6) A separate audio source or the audio output of one of
the video sources may be connected to the audio
input (white phono plug).
7) Connect the supplied plug-in power supply unit to
the red inline jack of the cable and to a socket
(200 – 240 V~/50 Hz or 60 Hz).
The monitor can, however, be connected to an-
other power source which supplies an operating volt-
age of 12 V
5 Inserting the Battery into the Remote
Control
Press the strap of the battery support to the right
(1
st
arrow in fig. 4) and pull out the support at the same
time (2
arrow in fig. 4). Insert the battery (3 V button
nd
cell, type CR2025) with the positive pole upwards into
the support and put it back.
6 Operation
When actuating the remote control, always direct it to
the infrared sensor (1) of the monitor. If it should fail to
function or its range should decrease, replace the bat-
tery (see chapter 5).
1) To switch on the monitor, press the button
the unit so that it locks into place. After 3 seconds the
picture of the video input last selected appears and
the insertion "AV1" (video source 1) or "AV2" (video
source 2).*
Note: The sound can only be heard if a video signal
is present at the video input selected.
2) To switch over between the video inputs, press
the button V1/V2 (9).
3) With the button MIR (3) it is possible to switch to
mirror-inverted picture display. Each time the
button is pressed, the monitor changes to another
picture display:
mirror inversion around the vertical axis
inversion around the vertical axis and horizontal axis
(picture rotation)
→
zontal axis
* The insertion "AV1" or "AV2" will immediately be extinguished by pressing the button
pressing the button MIR (3) [however, not at all, if no video signal is present at the selected video input]. "AV1" or "AV2" will be inserted for 30 seconds each time the
unit is switched on from the stand-by mode with the button
©
by MONACOR INTERNATIONAL GmbH & Co. KG, Bremen, Germany. All rights reserved.
Order No.
19.9680
st
video source, the black
nd
video
and shows a current rating of 650 mA.
(6) on
→
mirror
→
mirror inversion around the hori-
normal picture display.
(7) and each time the video source is changed with the button V1/ V2 (9).
4) To adjust the picture parameters and the volume,
it is possible to successively call the adjusting scales
BRIGHT (brightness), COLOR (colour intensity),
CONTRAST, TINT (only for NTSC sources), and
VOLUME with the button SELECT (4). With the scale
called, adjust the value for the parameter between
0 – 100 with the buttons V+ and V- (5).
To exit the last adjusting scale VOLUME, press
the button SELECT. Each scale will also be extin-
guished automatically 5 seconds after the last button
is pressed.
Notes:
a If no button has yet been pressed after switching
on, the insertion "AV1" or "AV2" will be extin-
guished when button SELECT is pressed for the
first time, and the adjusting scale BRIGHT will not
appear until the button is pressed for the second
time.
b The volume can also directly be changed with the
buttons V+ and V-, i. e. without calling the ad-
justing scale VOLUME.
5) It is possible to switch over between different picture
adjustments with the button P.P (10):
→
→
→
STANDARD
SOFT
LIGHT
For MEMORY, the picture parameters adjusted by the
user will apply (see operating step 4). For the other
four picture adjustments the parameters are preset.
Note: Each time the monitor is switched on with the
button
(6) always the picture parameters adjusted
by the user (MEMORY) will apply.
6) To mute the speaker, press the button
tion ]. To deactivate the mute feature, press the but-
ton again (short insertion
) or adjust the volume.
Note: The symbol
is extinguished as long as "AV1"
or "AV2" is inserted – after pressing the button
or the button V1/V2 (9).
7) To change to stand-by, press the button
the remote control; the stand-by indication (2) lights
up. To switch the monitor on again, press the button
once more.
8) To activate the automatic switching over to stand-
by, press the button SLEEP (11), then by pressing
this button several times, adjust the time (in min.)
after which the monitor automatically switches to
stand-by unless a button is actuated. The following
adjustments are possible: OFF (function switched
off), 15, 30, 45, 60, 75, 90, 105, 120. The adjusting
mode SLEEP is exited 5 seconds after the last button
is pressed.
Note: After an automatic switching over to stand-by
the adjustment is always reset to OFF.
9) To switch off the monitor, disengage the button
(6) on the unit.
7 Specifications
Diagonal screen size: . 14.2 cm (5.6")
Colour system: . . . . . . PAL/NTSC (automatic switch-
ing over)
Resolution: . . . . . . . . . hor. 960 × vert. 234 pixels
Video inputs: . . . . . . . . 1 Vpp/75 Ω
Audio input: . . . . . . . . . 30 mV/10 kΩ
Speaker: . . . . . . . . . . . 0.5 W
MAX
Ambient temperature: . 0 – 40 °C
Power supply: . . . . . . . 12 V , 650 mA
via supplied power supply unit
Connection cable
video and audio: . . . phono plugs
power supply: . . . . . . low voltage inline jack
5.5/2.1 mm (Ø outside/inside)
positive pole = inside contact
1
Mounting of the support: 6.3 mm (
/
4
Dimensions, weight: . . 155 × 120 × 35 mm, 380 g
Subject to technical modification.
(8), SELECT (4), V-/V+ (5), P.P (10), or SLEEP (11) and after 30 seconds by
A-0248.99.02.05.2007
®
→
MEMORY
VIVID.
(8) [inser-
(7)
(7) on
") thread
Publicidad
