Troubleshooting Guide; Cleaning Instructions - Good Earth Lighting G19920-WH-I Guia De Inicio Rapido

2
With a pencil, mark these locations on the wall, or other vertical
mounting surface (Fig. 1).
Fig. 1
3
Drill a small pilot hole for each screw, and screw the mounting
screws into the holes until only 1/16 in. of the screw head
protrudes from the wall.
For mounting into drywall, drill 3/16 in. holes for the plastic wall
Fig. 2
anchors (Fig. 2). Insert the plastic wall anchors into the proper
holes and tap them into place so they are flush with the surface of your drywall. Screw all
screws into the plastic anchors.
4
Position the back of the spot light over the screws so that the
Fig. 3
keyhole slots align with the screw heads. Slip the screw heads
into the back, and slide the spot light downward to lock the
screw heads in place (Fig. 3). If the light wobbles, or is not
firmly mounted against the wall, you may need to tighten the
mounting screws a little more to lessen the gap between the
back of the light and the surface of the wall.
Bulb Replacement Instructions
Relamp with: 120V/GU10 base/10-watt halogen MR11 bulb or smaller for G19920-WH-I,
120V/GU10 base/20-watt halogen MR16 bulb or smaller for G19935-WH-I.
1
Shut off power supply. Allow sufficient time for bulb to cool properly before handling.
2
Your bulb is held in place with a spring clip that locks into a
Fig. 1
recessed groove inside the top of the fixture. To remove the clip,
place your thumb over the crimped portion of the wire while
squeezing the 2 angled ends of the clip together and pulling up
(Fig. 1). NOTE: Wear protective eyegear when removing the
spring clip as it could fly out.
3
To remove the bulb, push the cord at the back of the fixture up
Fig. 2
(Fig. 2). Once the bulb has been pushed free of the fixture, hold
the socket and pull the bulb straight out with the other hand.
4
Insert the new bulb into the socket and pull the bulb/socket
Fig. 3
back into the fixture. IMPORTANT: Oils from your hands and
fingers may cause the bulb to overheat and burn out quickly.
Use a soft cloth when handling bulb (Fig. 3).
5
Push the bulb down into the housing far enough that you
can replace the spring clip into the bottom groove of the
housing (Fig. 4). Carefully push one side of the clip into the
groove at the top. The other side will lock into place to hold
Fig. 4

Troubleshooting Guide

Minor problems often can be fixed without the help of an electrician. Before doing any work on the
fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.
Problem Cause
Fixture doesn't light Bulb is defective
Power is off
Bad switch

Cleaning Instructions

Your fixture is made from quality materials that will last for many, many years with
minimum care. You may want to periodically clean the fixture using a mild, non-abrasive
glass cleaner and soft cloth. Do NOT use solvents or cleaners containing abrasive
agents. When cleaning the fixture, make sure you have the power turned off and do not
spray liquid cleaner directly onto the bulb, socket, ballast, or wiring.
the bulb securely (Fig. 5).
Fig. 5
Solution
Replace bulb
Check if power supply is on
Test or replace switch
- 3 -
Replacement Parts List
Keep this guide handy for
ordering replacement parts.
Need Help?
In the event you are missing a part or have questions regarding installation
please visit our website at www.goodearthlighting.com/support.html or
call the Customer Care Center 1-800-291-8838.
Good Earth Lighting
1 YEAR LIMITED WARRANTY
Good Earth Lighting, Inc. warrants this lighting fixture to be free from defects in materials and
workmanship for a period of one (1) year from the date of original purchase by the consumer.
If you are missing any parts, or have any questions about your installation, DO NOT RETURN
YOUR FIXTURE TO THE STORE! CALL US FIRST! We can often help get the problem corrected
right over the phone. You can call us at 1-800-291-8838, 9AM-5PM CST, Monday through Friday.
In the unlikely event the Good Earth Lighting fixture fails to perform as it was designed to do
within one (1) year from date of purchase, we will repair or replace (at our option) the unit in
the original color, and style if available, or in a similar color and style if the original item has
been discontinued, without charge. This warranty covers the entire fixture, EXCLUSIVE OF
LAMPS. Suspect units should be properly checked to ensure performance problems are not
lamp related. Defective units must be properly packed, and returned to Good Earth Lighting,
Inc. with a letter of explanation, and your original purchase receipt showing date of purchase.
Call us at 1-800-291-8838 to obtain a Return Authorization number, and an address where to
ship your defective product.
Note: No C.O.D. shipments will be accepted. The liability of Good Earth Lighting, Inc. is in any
case limited to replacement of the defective light fixture product. Good Earth Lighting, Inc. will
not be liable for any other loss, damage, or injury which is caused by the product. This
limitation upon the liability of Good Earth Lighting, Inc. includes any loss, damage, or injury
which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (III)
based upon theories of warranty, contact, negligence, strict liability, tort, or otherwise; or (IV)
directly, or indirectly related to the sale, use, or repair of the product.
Good Earth Lighting, Inc., 5260 Capitol Drive, Wheeling, IL 60090
©2009 Good Earth Lighting, Inc.
4509INS1992019935
Préparation
N'UTILISEZ PAS CE LUMINAIRE AVEC UN CIRCUIT DE GRADATEUR. Si vous avez actuelle-
ment des commutateurs à gradateur, vous devrez les enlever et les remplacer par des
interrupteurs d'éclairage ordinaires. Si vous avez un gradateur à trois positions, vous devrez
le remplacer par un commutateur à trois positions ordinaire. Si vous n'avez pas d'expérience
en matière d'installations électriques, nous vous recommandons de demander à un
électricien professionnel de réaliser votre installation.
Votre éclairage accentué par projecteur Good Earth Lighting® est la solution d'éclairage parfaite
pour mettre en valeur les œuvres d'art, les sculptures, les plantes ou d'autres décorations dans
votre habitation. Nous vous recommandons de lire toutes les instructions avant de commencer
votre installation. Vos projecteurs pour éclairage accentué Micro ou Mini peuvent être placés sur
le plancher ou sur une table, ou ils peuvent être montés sur le mur pour produire un éclairage
particulier. Les projecteurs pour éclairage accentué Micro & Mini comportent tous les deux un
interrupteur spécial de sécurité, situé dans la base du luminaire, qui éteint la lumière
automatiquement si le luminaire est renversé ou s'il tombe du mur.
N'installez PAS ce luminaire À L'INTÉRIEUR d'une armoire. Ce luminaire ne doit être utilisé qu'à
l'intérieur d'un immeuble. Ne le montez PAS au-dessus d'un lavabo ou d'une cuisinière. Ne tentez
PAS d'acheminer le cordon d'alimentation électrique à travers des armoires fixes, des murs ou une
retombée de plafond.
CONSIGNES DE SÉCURITÉ IMPORTANTES
Les lampes et les lentilles allumées sont TRÈS CHAUDES !
AVERTISSEMENT – Pour réduire le risque D'INCENDIE, DE CHOC ÉLECTRIQUE, D'EXPOSITION À
DES RAYONNEMENTS UV EXCESSIFS OU DE BLESSURE PHYSIQUE :
1. Éteignez/débranchez et laissez refroidir avant de remplacer l'ampoule (la lampe).
2. L'ampoule (la lampe) peut rapidement devenir TRES CHAUDE. Ne touchez que l'interrupteur/la
fiche pour allumer.
3. Ne touchez pas une lentille d'ampoule très chaude, ou son enceinte.
4. Ne restez pas devant la lumière si votre peau devient chaude.
5. Ne regardez pas directement une ampoule (une lampe) allumée.
6. Maintenez à une distance suffisante d'objets risquant de brûler ou de fondre.
7. Utilisez avec une ampoule halogène MR11 de 120 V/GU10 base/10 watts ou moins pour
G19920-WH-I ; avec une ampoule halogène MR16 de 120 V/GU10 base/20 watts ou moins pour
G19935-WH-I. Les ampoules de rechange doivent être des lampes halogènes au filament en
Hardware Kit
HDW19920
HDW19935
Warranty
®
Printed in China
- 4 -