Tabla de contenido
Publicidad
ELECTRICAL SPECIFICATIONS
Power supply
Medium consumption
(5)
Stand-by consumption
ENVIRONMENTAL CONDITIONS
Operating temperature
Relative humidity
Storage temperature
Storage relative humidity
ESC/POS
TM
EMULATION
Character density
Number of columns
Characters (L x H mm)-Normal
Character set
BARCODE READER SPECIFICATIONS (mod.CX002 model)
Scan rate
Sensors
Light source
Ambient light (
Fluorescent lamp)
Resolution
Readable Barcode
TRANSPONDER SPECIFICATIONS
Supported transponders
NOTES:
(1) Electronic board.
(2) "Veramono.ttf" and "Mono.ttf" are installed on printer fl ash disk. It
is possible to install additional TrueType fonts.
(3) The paper width value depends on the presence of paper guides
on triple feeder.
(4) For external rolls diameter higher to Ø100mm it's recommended
to use a paper pretensioning device.
(5) Referred to a standard CUSTOM receipt (L=10cm, Density =
12,5% dots on).
(6) Only for models with barcode reader.
(7) Only for models with reader/writer RFID.
(8) With optional ASK support also the ISO 14443B, Felica , Calypso
and also other minor RFID standards.
(9) Other UHF protocols are available with fi rmware upgrade
11 cpi
15 cpi
35
45
2,25x3
1,75 x 3
ALL UPC/EAN/JAN, Code 39, Code 39 Full ASCII, Code 128, Code 93,
Interleave 25, Industrial 25, Matrix 25, China Postage, CODABAR/NW7,
Code 11, MSI/PLESSEY, Code 32
(7)
HF high frequency RFID (13,5Mhz)
ISO 14443A (Mifare 1K, 4K) and Ultralight ISO 15693 (i-Code tags)
UHF ultra high frequency RFID (900 Mhz)
ETSI fully compliant to the European Regulation ETSI EN 300 220 (869.525 MHZ)
FCC compliant to the US telecommunication regulation FCC part 15 (902-928 MHZ)
ISO 18000-6B, Philips UCODE EPC 1.19 EPC Class1 Gen2
52
100Vac ÷ 240Vac
35 W
9 W
0-50°C
10-85% Rh
-20 °C – 70 °C
10% - 90% Rh
20 cpi
16 cpi
64
53
1,25 x 3
1,5x2
3
(6)
200 scans/sec
Liner CCD Sensor
Red Leds, 630 nm
3000 LUX MAX
5 mil. (0.127 mm)
NOTE:
(1) Scheda elettronica.
(2) Nella stampante sono già installati i font "Monovera.ttf" e "Vera.
ttf". E' possibile installare font aggiuntivi.
(3) Il valore della larghezza carta dipende dalla presenza di guide
carta nel gruppo di caricamento.
(4) Per rotoli con diametro esterno superiore a Ø100mm è consiglia-
to l'utilizzo di un ammortizzatore carta.
(5) Riferito ad uno scontrino tipico CUSTOM (L = 10cm, Densità =
12,5% dots accesi).
(6) Solo per modelli con lettore barcode.
(7) Solo per modelli con lettore/scrittore RFID.
(8) Con ASK opzionale, sono supportati anche i formati ISO 14443B,
Felica , Calypso e altri standard RFID minori.
(9) Altri protocolli UHF sono disponibili con l'aggiornamento fi rmwa-
re.
23 cpi
30 cpi
68
96
1,2x2
0,8x2
:
(8)
(9)
:
Publicidad
Tabla de contenido
