Operation And Maintenance; Technical Parameters - GRAPHITE 58G011 Manual Del Usuario

Cut at a uniform rate, pay attention to avoid overloading the jigsaw.
Excessive pressure applied on the blade will suppress pendulum
action and will affect cutting efficiency unfavourably. Decrease or
switch off the pendulum action completely when cutting along
gently curved line.
When the footplate does not rest on the processed material with
its whole surface but is lifted above, there is danger of kick back
or breaking the blade.
CUTTING A HOLE IN MATERIAL
• Make a hole in processed material with 10 mm diameter.
• Put blade into the hole and start cutting from that spot.
METAL CUTTING / TYPES OF BLADES
Use appropriate blades with more teeth for cutting of metal.
For metal cutting use appropriate lubricant (e.g. cutting oil). Metal
cutting without lubrication leads to rapid wear of blade. The below
table gives the best choices for blade type:
Teeth per Blade
Application range
inch length
24
14 80 mm
9
• Use only appropriate and sharp blades.
• Do not use blades with damaged shank.
• Use appropriate blade types.

OPERATION AND MAINTENANCE

Remove the battery from the device before commencing
any activities related to installation, adjustment, repair or
maintenance.
MAINTENANCE AND STORAGE
• Cleaning the device after each use is recommended.
• Do not use water or any other liquid for cleaning.
• Clean the tool with a dry cloth or blow through with compressed
air at low pressure.
• Do not use any cleaning agents or solvents, they may damage
plastic parts.
• Clean ventilation holes in the motor casing regularly to prevent
device overheating. Do not clean ventilation holes by inserting
sharp objects there, such as screwdrivers and other similar objects.
• Regular lubrication of guiding roller is recommended. A drop of oil
applied in this spot will prolong lifetime of the roller.
• In case of excessive commutator sparking, have the technical
condition of carbon brushes of the motor checked by a qualified
person.
• Always store the tool in a dry place, beyond reach of children.
• Store the device with the battery removed.
All defects should be repaired by service workshop authorized
by the manufacturer.

TECHNICAL PARAMETERS

RATED PARAMETERS
Cordless Jigsaw
Parameter
Battery voltage
Blade stroke cycles (without load)
Soft steel, non-ferrous metals
Non-ferrous metals, plastics
Wood, plywood:
Value
18 V DC
0-2400 spm
Maximum thickness of cut
material
Blade stroke length
Protection class
Weight
Year of production
Graphite Energy+ System Battery
Parameter
Battery
Battery voltage
Battery type
Battery capacity
Ambient temperature range
Charging time for charger 58G002
Weight
Year of production
Graphite Energy+ System Charger
Parameter
Charger type
Supply voltage
Power supply frequency
Charging voltage
Max. charging current
Ambient temperature range
Charging time of the battery 58G001
Charging time of the battery 58G004
Protection class
Weight
Year of production
NOISE LEVEL AND VIBRATION PARAMETERS
Noise and vibration information
Parameters of produced noise level, such as sound pressure level
Lp and sound power level Lw
A
are specified below in this manual, in compliance with EN 60745.
Vibration values a and measurement uncertainty K are
h
determined in accordance with EN 60745 and specified below.
Vibration level specified below in this manual was measured in
accordance with measurement procedure defined in EN 60745
and can be used to compare power tools. It can also be used for
initial assessment of exposure to vibrations.
Specified vibration level is representative for main applications
of the power tool. Vibration level may change if the power tool is
used for other purposes, with different working tools or will not
be maintained properly. The abovementioned factors may lead
to higher exposure to vibrations during whole working time.
To precisely define exposure to vibrations, include periods when
the power tool is switched off and when it is switched on but
not used for working. This way total exposure to vibrations may
be significantly lower. Use additional safety measures to protect
the user against results of exposure to vibrations, such as: power
tool and working tool maintenance, proper hand temperature
conditions, good work organisation.
15
Wood 80 mm
Metal 10 mm
25 mm
III
1,700 kg
2017
Value
58G001 58G004
18 V DC 18 V DC
Li-Ion Li-Ion
2000 mAh 4000 mAh
0 0 0 0
4 C – 40 C 4 C – 40 C
1 h 2 h
0,400 kg 0,650 kg
2017 2017
Value
58G002
230 V AC
50 Hz
22 V DC
2300 mA
4 0 C – 40 0 C
1 h
2 h
II
0,300 kg
2017
with measurement uncertainty K
A