Operation And Maintenance; Maintenance And Storage - GRAPHITE 58G017 Manual Del Usuario

Switching off
• Release pressure on the switch button (6) to stop the tool.
Device speed within its range is controlled with pressure on the
switch button.
CUTTING
• Place the front part of the base (2) flat on the material for
processing, so the blade does not have contact with the material.
• Start the saw and adjust working speed to properties of processed
material.
• Move the saw slowly and guide the blade along previously set
cutting line (fig. H, I).
Cut at a steady rate, be careful not to overload the saw. Excessive
pressure applied on the blade will suppress operation and will affect
cutting efficiency unfavourably.
During operation whole surface of the base should contact
surface of the processed material.
Make sure that the working tool is installed properly. Improperly
or inaccurately installed working tools can slip during operation
and cause risk for the user.

OPERATION AND MAINTENANCE

Remove the battery from the device before commencing
any activities related to installation, adjustment, repair or
maintenance.

MAINTENANCE AND STORAGE

• Cleaning the device after each use is recommended.
• Do not use water or any other liquid for cleaning.
• Clean the device with a dry cloth or blow through with
compressed air at low pressure.
• Do not use any cleaning agents or solvents, they may damage
plastic parts.
• Clean ventilation holes in the motor casing regularly to prevent
device overheating.
• Always store the tool in a dry place, beyond reach of children.
• Store the device with the battery removed.
All defects should be repaired by service workshop authorized by
the manufacturer.
Cordless Reciprocating Saw 58G017
Parameter
Supply voltage
Idle oscillation speed
Working tools attachment system
Blade stroke length
Maximum thickness of cut material
(wood)
Maximum thickness of cut material
(steel)
Protection class
Weight
Year of production
58G017 defines type and indication of the device
Graphite Energy+ System Battery
Parameter
Battery
Battery voltage
Value
18 V DC
0-3000 rpm
tool free
22 mm
60 mm
6 mm
III
1,85 kg
2019
Value
58G001 58G004
18 V DC 18 V DC
13
Battery type
Battery capacity
Ambient temperature range
Charging time for charger 58G002
Weight
Year of production
Graphite Energy+ System Charger
Parameter
Charger type
Supply voltage
Power supply frequency
Charging voltage
Max. charging current
Ambient temperature range
Charging time of the battery 58G001
Charging time of the battery 58G004
Protection class
Weight
Year of production
NOISE LEVEL AND VIBRATION PARAMETERS
Sound pressure (sanding)
Sound power (sanding)
Vibration acceleration (cutting
wood – main handle)
Vibration acceleration (cutting
wood – additional handle)
Vibration acceleration (cutting
metal sheet – main handle)
Vibration acceleration (cutting
metal sheet – additional handle)
Noise and vibration information
Noise produced by the device is defined with: level of produced
sound pressure Lp and level of sound power Lw
A
measurement uncertainty). Vibrations produced by the device
are defined with vibration acceleration value a
measurement uncertainty).
Sound pressure Lp , sound power Lw
A
specified in this manual have been measured in accordance with EN
60745-1. Specified vibration level a
and for initial evaluation of exposition to vibrations.
Specified vibration level is representative for main applications
of the device. When the device is used for other purposes or with
different working tools, the vibration level may change. Insufficient
or too rare maintenance may increase vibration level. The
abovementioned factors may lead to higher exposure to vibrations
during whole working time.
To precisely define exposure to vibrations, include periods when
the device is switched off and when it is switched on but not used
for working. Once all factors have been carefully considered, total
exposition to vibrations may be significantly lower.
To protect the user from results of exposure to vibrations, use
additional safety measures such as: device and working tool periodic
maintenance, proper hand temperature conditions, good work
organisation.
Li-Ion Li-Ion
2000 mAh 4000 mAh
4 0 C – 40 0 C 4 0 C – 40 0 C
1 h 2 h
0,400 kg 0,650 kg
2019 2019
Value
58G002
230 V AC
50 Hz
22 V DC
2300 mA
4 0 C – 40 0 C
1 h
2 h
II
0,300 kg
2019
Lp = 82,31 dB(A) K= 3 dB(A)
A
Lw = 93,31 dB(A) K= 3 dB(A)
A
2 2
a = 18,728 m/s K= 1,5 m/s
h
a = 15,044 m/s 2 K= 1,5 m/s 2
h
a = 6,422 m/s 2 K= 1,5 m/s 2
h
2 2
a = 5,511 m/s K= 1,5 m/s
h
(where K is
A
(where K is
h
and vibration acceleration ah
A
can be used to compare tools
h