Maintenance Of Your Opener; Replacement Parts - Chamberlain LiftMaster Professional 410E Manual De Instrucciones

MAINTENANCE OF YOUR OPENER

Once a Month:
• Repeat safety reverse test. Make any necessary adjustments.
• Manually operate door. If it is unbalanced or binding, call for
professional garage door service.
• Check to be sure door opens and closes fully. Adjust Limits and/or
Force if necessary.
Once a Year:
Oil door rollers, bearings and hinges. The opener does not require
additional lubrication. Do not grease the door tracks.
SPECIAL FEATURES OF THE 4210E/4410E – 26
A. Door within a door connection
Remove cover. Locate auxiliary terminal block. Remove jumper
from terminal leads 1 and 2 (not shown). Replace with contact
switch leads as shown.
B. Flashing light connection
The flashing light can be installed anywhere. Connect light leads to
terminals 3 and 4 on the terminal block.
C. Coaxial antenna adapter
A coaxial antenna connection can be used if the transmitter range
is too short. Cut off the existing antenna. Use standard coax cable
and connector. Strip off end of insulation to "X" dimension.
433 MHz: X = 250mm
Reposition antenna.
27
ACCESSORIES –
433MHz 27MHz
(1) Models 4330E 750E
(2) Models 4332E 752E
(3) Model 4333E
(4) Model
754E
(5) Model
4335E
(6) Models 747E 727E
(7) Model 58LM...............................Multi-Function Door Control Panel
(8) Model 760E ...............................Outside Keylock
(9) Model 1702E .............................Outside Quick Release
(10) Model 770E ...............................The Protector System™
(11) Model 1703E .............................The Chamberlain Arm™
(12) Model FLA230...........................Flashing Light Kit
(13) Model 16200LM ........................Pedestrian Door Switch
(14) Model MDL100LM.....................Mechanical Door Latch Kit
(15) Model EQL01 ............................Door Handle Quick Release
(16) Model 100027 ...........................1-Position Key Switch
Model 100041 ...........................2-Position Key Switch
WIRING INSTRUCTIONS FOR ACCESSORIES
Keyless Entry System – To opener terminals: Red-1 and White-2
Outside Keylock – To opener terminals: Red-1 and White-2
Protector System™ – To opener terminals: White-2 and Black-3
Door Control Panel – To opener terminals: Red-1 and White-2
114A2074I-GB
27 MHz: X = 2,44m
Single-Function Remote Control
2-Function Remote Control
3-Function Remote Control
4-Function Remote Control
3-Function Mini Remote Control
Keyless Entry System
(Flush Mount - 100010)
(Flush Mount - 100034)

REPLACEMENT PARTS

SPECIFICATIONS
Max. Pull Force...............800N
Watts ..............................550
Type................................Permanent split capacitor
Speed .............................1500 rpm
Volts................................230-240 Volts AC-50Hz Only
Gears ..............................16:1 worm gear reduction
Drive ...............................Chain with one-piece trolley on
Length of Travel..............Adjustable to 2,3m (7-1/2 feet)
Travel Rate .....................5"-7" (127-178mm) per second
Lamp...............................On when door starts, off 4-1/2 minutes
Door Linkage ..................Adjustable door arm. Pull cord trolley
Personal .........................Push button and automatic reversal in down
Electronic ........................Independent up and down force
Electrical .........................Motor overload protector and low voltage
Limit Device ....................Circuit actuated by limit nut.
Limit Adjustment .............Screwdriver adjustment on side panel.
Start Circuit .....................Low voltage push button circuit.
Length (Overall) ..............3,1m (122-1/2")
Headroom Required .......5cm (2")
Hanging Weight ..............32 lb (14,5 kg)
Memory Registers...........12
Code Switch Memory .....1
Keypad Code Memory ....1
© Chamberlain GmbH, 2006
28 – 29
Motor
Drive Mechanism
steel T-rail.
after stop.
release.
Safety
direction. Push button and automatic stop in
up direction.
adjustment screws.
push button wiring.
Dimensions
Receiver