Technical Data; Declaration Of Conformity - Bosch 0 607 350 198 Manual Original

OBJ_BUCH-1326-005.book Page 17 Monday, October 10, 2016 3:12 PM

Technical Data

Pneumatic Random Orbit Sander
Article number 0 607 350 ...
No-load speed n
0
Stroke
Sanding sheetØ
Max. working pressure for tool
Thread size of hose connection
Inner diameter of hose
Air consumption at no-load
Weight according to EPTA-Procedure 01:2014
Noise/Vibration Information
Sound emission values determined according to EN ISO 15744.
The noise level when working can exceed 80 dB(A). Wear hearing protection!
Typically the A-weighted noise level of the pneumatic tool is:
Sound pressure level L
pA
Uncertainty K
Vibration total values a (triax vector sum) and uncertainty K determined according to EN 28927:
h
a
h
K
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN ISO 11148 and may be used to compare one
pneumatic tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the pneumatic tool. However if the pneumatic
tool is used for different applications, with different accesso-
ries or insertion tools or is poorly maintained, the vibration
emission may differ. This may significantly increase the expo-
sure level over the total working period.
An exact estimation of the level of exposure to vibration
should also take into account the times when the pneumatic
tool is switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level over
the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintaining the pneu-
matic tool and the accessories, keeping the hands warm, or-
ganisation of work patterns.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical data" complies with all applicable
provisions of the directive 2006/42/EC including its amend-
ments and is in conformity with the following standards:
EN ISO 11148-8.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ECS,
70538 Stuttgart, GERMANY
Bosch Power Tools
... 198
-1
min 12000
mm 2.5
mm 80
bar 6.3
psi 91
1/4" NPT 1/4" NPT
mm 10
l/s 8.3
cfm 17.6
kg 0,62
lbs 1,3
dB(A) 73
dB 3
2
m/s < 2.5
2
m/s 1.5
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ECS
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
Connecting the Air Supply (see figure A)
 Ensure that the air pressure is not lower than 6.3 bar
(91 psi) because the pneumatic tool is designed for
this operating pressure.
For maximum performance, the values for the inner hose di-
ameter as well as the connection threads must be adhered to
as listed in the "Technical Data" Table. To maintain the full
performance, only use hoses with a maximum length of 4 m.
The compressed air supplied should be free of foreign materi-
al and moisture to protect the tool from damage, contamina-
tion, and the formation of rust.
Note: The use of a compressed-air maintenance unit is neces-
sary. This ensures proper function of the pneumatic tools.
Observe the operating instructions of the maintenance unit.
All fittings, connecting lines and hoses must be dimensioned
for the pressure and the required air volume.
English | 17
... 199 ... 200
12000 12000
5.0 2.5
150 150
6.3 6.3
91 91
1/4" NPT
10 10
8.5 8.5
18.0 18.0
0,68 0,72
1,5 1,5
76 76
3 3
3.1 3.1
1.5 1.5
1 609 92A 39N | (10.10.16)