GRAPHITE 59G812 Instrucciones De Uso página 13

6. Keep children away from tools
7. Protect the device against moisture
8. Second protection class
9. Danger! Watch your hands
10. Attention laser radiation! Do not look into the laser beam.
CONSTRUCTION AND APPLICATION
The mitre saw is a device equipped with the base that provides
the possibility to change the angle of the cutting head attached
to it. In addition, depending on a design, the mitre saw head can
be tilted at an angle or slid out to increase the functionality and
cutting length.
The mitre saw is designed for cutting wooden pieces that match
with the tool size. Do not use the saw for cutting firewood. Use
the mitre saw accordingly to its purpose only. Attempts to use the
mitre saw for purposes other than specified will be considered an
improper use. Use the mitre saw only with appropriate cutting
discs with teeth with sintered carbide inserts. The mitre saw is
designed for carpentry works in workshops and for joinery works.
The power tool should be used according to its purpose!
DESCRIPTION OF GRAPHIC PAGES
The below list refers to device components shown in the
graphic pages of this instruction manual.
EQUIPMENT AND ACCESSORIES
1. Dust bag
2. Socket wrench
3. Vertical clamp
PREPARATION FOR WORK
Make sure the mitre saw is disconnected from power
supply, before any adjusting or mounting works are
commenced.
HANDLING THE MITRE SAW
• Make sure the head is locked in the lowest position when
carrying the mitre saw.
• Make sure that the work table locking knob, head locking
lever, and other safety parts are tightened firmly.
INSTALLING THE MITRE SAW ON A WORKSHOP BENCH
It is recommended to fix the mitre saw to a workbench or a
stand with the use of mounting holes (19) designed for such
purpose. They are located on the mitre saw base and
guarantee safe operation and eliminate risk of unwanted
machine shifts during operation. The holes allow to use bolts
with hexagonal head and 8 mm in diameter.
- 1 pcs
- 1 pcs
- 1 pcs
When fixing the mitre saw to a workbench ensure that:
• The workbench top surface is flat and clean.
• Screws and bolts are tightened equally and moderately
(mounting bolts must be tightened so the base is not stressed
or deformed). In case of over-stress there is danger of
breaking the base.
DUST EXTRACTION
To prevent dust accumulation and provide maximum efficiency, you
can connect the mitre saw to an industrial vacuum cleaner using
the dust extraction connector (28) Alternatively, you can collect the
dust in the dust-bag (included) after installing it onto the dust
extraction connector. To install, put the dust bag (29) onto the dust
extraction connector (28) (fig. A). To empty the dust bag, remove it
from the dust extraction outlet and open the zip-fastener that allows
to access inside the bag.
To achieve optimal dust extraction empty the bag when it is
2/3 full.
USING THE EXTENSION ARM (HEAD)
There are two positions of the extension arm – upper and lower. To
release the extension arm from locked lower position, do as follows:
• Press and hold down the extension arm.
• Pull the head locking pin (9).
• Hold the extension arm as it raises to its upper position.
• To lock the extension arm in the lower position, do as
follows:
• Press and hold the disc guard lever (5).
• Release the pressure downwards onto the extension arm
until it is located in its lower position.
• Lock the extension arm in this position, sliding the head
locking pin in (9).
VERTICAL CLAMP
The vertical clamp (fig. B) can be installed in the saw base at
either side of the work table and is fully adjustable to size of
the workpiece to be cut. Do not use the saw without using the
vertical clamp.
• Loosen the vertical clamp mounting knob (30) to the base
on the side, which the vertical clamp will be installed.
• Install the vertical clamp by sliding it into the hole in the
mitre saw base and tighten the vertical clamp mounting knob
(30) to the mitre saw base.
• Once the vertical clamp arm position is adjusted (31) to the
workpiece, tighten the vertical clamp arm locking knob (32)
and workpiece mounting knob (33).
• Make sure the workpiece is secured.
OPERATION / ADJUSTMENTS
Make sure the mitre saw is disconnected from power supply,
before any adjusting or mounting works are commenced. To
ensure safe, precise and efficient operation of the mitre saw,
proceed with all adjustment procedures as a whole.
After finishing all the setting and adjustment procedures,
ensure that all spanners are collected. Check that all threaded
connections are properly tightened.
When making adjustments, ensure that all external parts work
properly and are in good condition. Any worn or damaged part
must be replaced by qualified personnel before starting to use
the mitre saw.
SWITCHING ON /SWITCHING OFF
The mains voltage must correspond to the value specified
on the mitre saw nameplate.
12