User Maintenance - Andis MLC Instrucciones De Uso Y Cuidado

USER INSTRUCTIONS
• The battery is not intended to be replaced by the user.
• The battery must be removed from the appliance before it is scrapped.
• The appliance must be disconnected from the supply mains when removing the battery.
• The battery is to be disposed of safely.
CHARGING CLIPPER USING CHARGING STAND
The AC adapter is intended for use with Andis model MLC lithium-ion clipper battery with a rated capacity of
4.5V 1.2A. Remove the clipper and AC adapter from the carton. Plug the AC adapter into a 120-240V AC
outlet, or according to your local power standards. Plug the adapter cord into the receptable on the back of
the charging stand (Figure H). Place clipper in the charging stand. The ON/OFF switch on the clipper must
be in the OFF position for the battery to charge. The blue light on the clipper will fade in and out while
charging. Note that the clipper can be removed at any time during the charging cycle without harming the
clipper or battery. Once the battery is fully charged, the light on the clipper (Figure I) will turn solid blue.
The clipper has not been charged at the factory. Please charge the clipper for 2 hours before the first
use for maximum performance.
You can keep the clipper plugged into the charging stand or adapter when not in use. The charging stand
or adapter will maintain the battery at full charge. We recommend that the charging stand or adapter be
unplugged if the clipper won't be used for seven or more days.
FAILURE TO CHARGE
1. Make sure voltage is present at the wall outlet (confirm with an appliance you know is working).
2. Make sure on/off switch on the clipper is OFF.
3. Check to make sure adapter cord is plugged firmly into clipper or charging stand. Twist the adapter cord
slightly to ensure good electrical connection.
4. If failure to charge still exists, return clipper to Andis or an Andis authorized service station for
examination and repair or replacement.
CORDED OPERATION
If the clipper powers OFF in the middle of a clipping job, the power cord can be attached to continue use in
corded operation. Plug the adapter cord directly into the bottom of the clipper (Figure I). When the clipper
is running with the adapter cord attached, the blue light will remain solid ON to indicate strong power, even
if the battery is not fully charged. The clipper will charge at a slower rate while in use with the cord
attached.
8
CLIPPER INDICATOR LIGHTS
When the clipper is running in a cordless
operation, a blue clipper indicator light means
the battery has a strong charge. When the light
turns red (Figure I) the battery level is low and
should be recharged as soon as possible. If the
clipper automatically powers OFF, move the
power switch to the OFF position and either
charge in the charging stand or plug in to cord to
continue trimming.
The clipper automatically powering off protects
the lithium-ion battery and is not a malfunction.
The clipper will resume normal operation when it
is recharged or plugged in to its power cord. The
MLC clipper, by design, will run at full power
until the battery is fully depleted.
USING ATTACHMENT COMBS
(Some models do not have combs and sizes will vary by kit)
To use, slide front of attachment comb over the teeth of the blade. Snap comb down over back of blade
(Figure J). Use the clipping guide to find the approximate lengths of cut. Different blade angles in relation to
the skin, thickness and texture of the hair will vary the cutting length.
CLIPPER BLADE ADJUSTMENT
Your Andis adjustable clipper blade set is easy to adjust. From coarse to fine cuts, all that is needed is a flick
of the adjustment lever with your thumb. In the upright position, the blades are set for the finest, or
shortest cuts (Figure K).

USER MAINTENANCE

Cleaning and user maintenance shall not be made by children
without supervision.
If clipper is not going to be used for a long period of time, store in a safe, cool, dry place. Do not wrap
adapter cord tightly around clipper. Do not hang the clipper by the adapter cord.
CLIPPER INDICATOR LIGHT STATUS
Clipper in Charging Stand
Fully Charged Solid Blue
Charging Blue Fade In and Out
Clipper in Use (Cordless)
Full Charge Solid Blue
Low Charge Solid Red
Clipper in Use (Corded)
Running Solid Blue
OFF with Full Charge Solid Blue
OFF without full charge Blue Fade In and Out
9