Franke CRYSTAL CR 86 M F Serie Manual De Instalación Y Servicio página 16

Horno multifunción
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 79
EN
CL 85 M / CM 85 M / CR 86 M _/F / SM 86 M _/F / SMP 86 M_/F
To clean the lower part of the oven,
it is advisable to remove any stains while
the oven is still warm; stains are easy
to deal with when fresh.
Cleaning the oven door
X
X
The oven door must be cleaned
(internally and externally) when the oven
is completely cold, using hot water. Do not
use abrasive cloths. Clean the glass using
special detergents.
X
X
Clean the enamelled surfaces with
hot water and non-abrasive detergent, just
as for the oven interior itself.
Models CR 86 only
The oven door decorative plastic panel can
be removed for more thorough cleaning.
X
X
With the door open,
press at the sides and
remove the panel, as
shown in the figure.
X
X
To refit the panel in the
oven door, just slide it in
place and press lightly
to engage the side
fastenings.
Removing the oven door internal glass
(models CL, CR, SM, SMP only) (Fig. 2)
The glasses of the oven door can be removed
to enable thorough cleaning of the internal
glasses, by proceeding as follows:
X
X
With the door completely open, turn the two
black blocks (with the word „CLEAN")
at the bottom of the door 180° so that they
fit into the seats in the oven structure.
Note: Make sure you turn them fully
(the blocks will click into this position).
X
X
Carefully lift the internal glasses: the two
blocks will prevent the door from closing
(if the blocks are not turned fully, removing
the glasses will cause immediate closing
of the door).
X
X
After carrying out the cleaning operations,
refit the internal glasses (the correct
position is indicated by the words
„TEMPERED GLASS" which must
be perfectly legible) and turn the two glass
retaining blocks back to their original
position.
Never try closing the door when only
one or both blocks have partially or completely
freed the internal glass panels. After cleaning,
always remember to turn both blocks before
closing the door.
Removing the oven door internal glass
(models CM only) (Fig. 3)
The glass of the oven door can be removed
to enable thorough cleaning of the internal
glass, by proceeding as follows:
X
X
With the door completely open, turn
the two black blocks at the bottom
of the door 180° (fig. 3a and 3b).
Note: Make sure you turn them fully
(the blocks will click into this position).
X
X
Carefully lift the internal glass (Fig. 3c):
the two blocks will prevent the door from
closing (if the blocks are not turned fully,
removing the glass will cause immediate
closing of the door).
X
X
To remove the glass in between, slide out
the two side gaskets (Fig. 3d) and then lift
out the glass (Fig. 3e).
X
X
After carrying out the cleaning operations,
refit the intermediate glass (Fig. 3f)
(the correct position is indicated
by the wording „TEMPERED GLASS" which
must be perfectly legible) by inserting
it carefully into the relevant grooves
located at the top of the door and pushing
it all the way to the end of the groove.
X
X
Then replace both gaskets (Fig. 3g), taking
extra care to ensure they are inserted
as far as possible, until they come into
contact with the upper edge of the door.
X
X
Finally, refit the internal glass (Fig. 3h) and
turn the two glass retaining blocks back
to their original locking position.
Never try closing the door when only
one or both blocks have partially or completely
freed the internal glass panels. After cleaning,
always remember to turn both blocks before
closing the door.
– 16 –

Publicidad

Tabla de contenido
loading

Tabla de contenido