Laser Safety; Product Familiarisation - Triton TCMS 254 Instrucciones De Uso Y De Seguridad

EN
l) Do not use another person as a substitute for a table extension or as
additional support. Unstable support for the workpiece can cause the blade to
bind or the workpiece to shift during the cutting operation pulling you and the
helper into the spinning blade.
m) The cut-off piece must not be jammed or pressed by any means against the
spinning saw blade. If confined, i.e. using length stops, the cut-off piece could
get wedged against the blade and thrown
n) Always use a clamp or a fixture designed to properly support round
material such as rods or tubing. Rods have a tendency to roll while being cut,
causing the blade to "bite" and pull the work with your hand into the blade.
o) Let the blade reach full speed before contacting the workpiece. This will
reduce the risk of the workpiece being thrown.
p) If the workpiece or blade becomes jammed, turn the mitre saw off. Wait for
all moving parts to stop and disconnect the plug from the power source
and/or remove the battery pack. Then work to free the jammed material.
Continued sawing with a jammed workpiece could cause loss of control or
damage to the mitre saw.
q) After finishing the cut, release the switch, hold the saw head down and wait
for the blade to stop before removing the cut-off piece. Reaching with your
hand near the coasting blade is dangerous.
r) When blade is binding, or when interrupting a cut for any reason, release
the trigger and hold the saw motionless in the material until the blade
comes to a complete stop. Never attempt to remove the saw from the work
or pull the saw backward while the blade is in motion or kickback may
occur. Investigate and take corrective actions to eliminate the cause of blade
binding.
s) When restarting a saw in the workpiece, centre the saw blade in the kerf
and check that saw teeth are not engaged into the material. If saw blade is
binding, it may walk up or kickback from the workpiece as the saw is restarted.
t) Blade depth and bevel adjusting locking levers must be tight and secure
before making cut. If blade adjustment shifts while cutting, it may cause binding
and kickback.
u) Check lower guard for proper closing before each use. Do not operate the
saw if lower guard does not move freely and close instantly.
v) Hold the handle firmly when making an incomplete cut or when releasing
the switch before the saw head is completely in the down position. The
braking action of the saw may cause the saw head to be suddenly pulled
downward, causing a risk of injury.
w) Do not use this saw to cut tree limbs or logs.
x) Never use blades recommended for operation at less than the rated no load
speed of the saw.
y) Do not use this saw to cut fibre cement board. This saw is not intended to cut
fibre cement boards.
z) Even when this tool is used as prescribed it is not possible to eliminate all
residual risk factors. If you are in any doubt as to safe use of this tool, do not
use it
WARNING: The operation of any mitre saw can result in foreign objects being
thrown into your eyes, which can result in severe eye damage. Before beginning
power tool operation, always wear safety goggles or safety glasses with side shield
and a full-face shield when needed.
WARNING: If any parts are missing, do not operate your mitre saw until the
missing parts are replaced. failure to follow this rule could result in serious personal
injury.
WARNING: When drilling, sanding, sawing or grinding, dust particles will be
produced. In some instances, depending on the materials you are working with, this
dust can be particularly harmful to you (e.g. lead from old gloss paint). You are
advised to consider the risks associated with the materials you are working with and
to reduce the risk of exposure.
You should:
• Work in a well-ventilated area.
• Work with approved safety equipment, such as those dust masks that are
specially designed to filter microscopic particles.

Laser Safety

• The laser used in this device is a Class 1M laser with maximum power of
≤ 0.39 mW and a wavelength of 400–700nm
• These lasers do not normally present an optical hazard, although staring at the
beam may cause flash blindness
WARNING: AVOID DIRECT EYE CONTACT.
A hazard may exist if you deliberately stare into the beam. Please observe all safety
rules as follows:
• The laser shall be used and maintained in accordance with the manufacturer's
instructions
tritontools.com
violently.
• Do not switch on the laser light until the tool is ready to cut
• Never aim the beam at any person, and particularly not into the eyes of any
person or animal, or any object other than the workpiece
• Always ensure the laser beam is aimed at a sturdy workpiece without reflective
surfaces. i.e. wood or rough-coated surfaces are acceptable. Reflective sheet
steel or similar is not suitable for laser use as the reflective surface could direct
the beam back at the operator
• Do not change the laser light assembly. Repairs must only be carried out by the
laser manufacturer or an authorised agent. Do NOT exchange with a different
type of laser
WARNING: Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation exposure.
Please refer to the relevant EN standards, EN 60825-1:2014 for more information
on Lasers.

Product Familiarisation

1. Operating Handle
2. Safety Lock
3. Lower Blade Guard
4. Base
5. Table Insert
6. Quick-cam Locking Lever
7. Mitre Handle
8. Mitre Detent Override
9. Mitre Table
10. Stop Plate
11. Guide Fence
12. Hold-down Clamp
13. Slide Carriage
14. Slide Carriage Lock Knob
15. Laser Horizontal Adjustment Knob
16. Laser Vertical Adjustment Knob
17. ON/OFF Trigger Switch
18. Laser ON/OFF Switch
19. Carry Handle
20. Dust Port
21. Cutting Depth Adjusting Knob
22. Cable Brackets
23. Hold-Down Latch
24. Guide Fence Locking Lever
25. Extension Table
26. Mounting Hole
27. Positive Stop Detent
28. Blade
29. Table Support Rod
30. Positive Stop Locking Lever
31. Dust Bag
32. Support Rod
33. Support Rod Screw
34. Handle Screw
35. Blade Spanner
36. Mitre Handle Hole
37. Support Rod Mounting Hole
38. Hold-down Clamp Locking Knob
39. Hold-down Clamp Mounting Holes
40. Bevel Locking Handle
41. Bevel Stop Plate
42. Stop Block
43. Bevel Detent Stop Pin
44. Workpiece
45. Extension Table Locking Lever
46. Stop Plate Locking Screw
47. Combination Square (Not supplied)
48. Bevel Adjustment Bolts
49. Bevel Pointer Screw
50. Bevel Pointer
51. Left Bevel Locknut
52. Left Angle Adjustment Bolt
53. Right Bevel Locknut
54. Right Angle Adjustment Bolt
55. Hex Screw
56. Mitre Pointer
57. Pointer Fixing Screw
58. Fence Locking Bolts
59. Stop Fixing Nut
60. Lever Adjustment Lock Nut
61. Support Rod Adjustment Nut
62. Depth Stop Block
Original Instructions
10