Behringer POLY D Guia De Inicio Rapido página 19

(2) (3)(4)(5)
(6) (7)(8)(9)
Sequencer Section
(1) TEMPO/GATE LENGTH – this knob controls
the sequencer and arpeggio tempo. During
step editing, it also controls the GATE length.
If SHIFT is held, then the knob also adjusts
the SWING.
(2) HOLD/REST – during pattern playback, this
allows you to hold the current step. During
step editing, it allows you to enter a rest.
(3) RESET/ACCENT – during playback, this allows
you to reset the pattern back to step 1. During
step editing, you can add an accent to a step.
(4) ARP (SET END) – press ARP and play any
keys, to create an arpeggio. Press HOLD
and ARP to hold the arpeggio. In Sequencer
mode, pressing SHIFT and SET END together,
followed by a STEP switch, will allow that step
to become the end of the current pattern.
(5) PATTERN (BANK) – This switch is used to
access either the current pattern, or bank
number, as follows:
PATTERN: Press PATTERN, and one of the 8
LOCATION LEDs will show the current pattern
number (from 1 to 8). To change to a different
pattern number, keep the PATTERN switch
held down and press any of the STEP switches
(1 to 8), or press <KYBD to decrease, or STEP>
to increase the pattern number.
BANK: Press SHIFT and PATTERN, and one of
the 8 LOCATION LEDs will show the current
bank number (from 1 to 8). To change to a
different bank number, keep both SHIFT and
BANK held down, and press any of the STEP
switches (1 to 8), or press <KYBD to decrease,
or STEP> to increase the bank number.
(1)
(10)
(11) (12) (13)
(6) SHIFT – This is used to access the secondary
features of some of the other sequencer
controls, such as SET END, BANK, SWING,
KYDB, and STEP. Hold down SHIFT and the
other switch at the same time. For example
SHIFT + PATTERN (BANK) will show the
current BANK number in the LOCATOR LEDs.
(7) PAGE – each pattern can be up to 32 steps in
length. This switch allows you to show each
of the 4 pages of 8 steps each. The LOCATION
LEDs 1 to 4, show which page you are on. If a
pattern is playing, the STEP LEDs will show the
steps in use on the current page.
(8) PLAY/STOP – starts or stops the playback of
the pattern. If SHIFT is held at the same time,
then this is the start of the pattern saving
procedure, described below.
(9) REC – press this to begin the recording of
a new pattern. This is also used with SHIFT
during the pattern saving procedure.
LOCATION – these multi-colored LEDS show
(10)
various details, such as the current PATTERN
number, current BANK number, current PAGE,
and GATE LENGTH.
KYBD – press SHIFT + KYBD to change the
(11)
sequencer to keyboard mode.
STEP – press SHIFT + STEP to change the
(12)
sequencer to STEP mode.
STEP SWITCHES – these multi-function
(13)
switches allow you to view and select individual
pattern steps, select a pattern number, select a
pattern bank. They are used during recording of
a pattern to show the current step. Active steps
are illuminated with a steady red LED, and the
current step flashes red.
Quick Start Guide
(14)
(15)
GLIDE KNOB – during step editing, this knob
(14)
can be used to add a Ratchet by splitting the
current step into 1, 2, 3, or 4 parts. Hold down
SHIFT and turn the knob to split the current
step into the number of parts shown by the
LOCATOR LEDs (yellow) 1 to 4.
GLIDE SWITCH – the GLIDE switch does not
(15)
have to be on for the Ratchet to work.
19