Nice Robus 600 Manual Del Usuario página 9

Alt
Apartment block open
Photo
Safety function
Photo 2
Safety function
Photo 3
Safety function
Master Step Step
Master open
Master close
Slave Step Step
Slave open
Slave close
Alt on closing
program the required operating mode,
selecting in Table 1-L ("command con-
figuration" > "alt on closing" > operat-
ing mode...)
Opening
program the required operating mode,
apartment block 1 open ("command
configuration" > "opening" > operating
mode apartment block 1 open)
Photo
program the required operating mode,
selecting in Table 1-F ("command config-
uration" > "photo" > operating mo de...)
Photo 2
program the required operating mode,
selecting in Table 1-H ("command con-
figuration" > "photo 2" > operating
mo de...)
Photo 3
program the required operating mode,
selecting in Table 1-I ("command config-
uration" > "photo 3" > operating mo de...)
Step step
program the required operating mode,
open - stop - close - open ("command
configuration" > "step step" > operating
mode: open - stop - close - open)
Opening
program the required operating mode,
selecting in Table 1-C ("command con-
figuration" > "opening" > operating
mo de...)
Closing
program the required operating mode,
selecting in Table 1-D ("command
con figuration" > "closing" > operating
mo de...)
Step step
program the required operating mode,
open - stop - close - open ("command
configuration" > "closing" > operating
mo de: open - stop - close - open)
Opening
program the required operating mode,
selecting in Table 1-C ("command con-
figuration" > "opening" > operating
mo de...)
Closing
program the required operating mode,
selecting in Table 1-D ("command con fig-
uration" > "closing" > operating mo de...)
When this command is sent, the control unit sto -
ps the manoeuvre in progress and activates the
application to execute the set operating mode.
Input configured as normally closed.
When this command is sent, the control unit
ac tivates the application to perform the opening
manoeuvre only until the limit switch is reached.
Note – This command is useful when using
control photocells or a magnetic detector loop.
Input configured as normally open.
When this command is sent, the control unit
activates the application according to the se -
lected manoeuvre type.
Input configured as normally closed.
When this command is sent, the control unit
activates the application according to the
selected manoeuvre type.
Input configured as normally closed.
When this command is sent, the control unit
activates the application according to the se -
lected manoeuvre type.
Input configured as normally closed.
When this command is sent, the control unit
activates the master (primary) leaf of the appli-
cation to complete the next manoeuvre follow-
ing the previous one (or still in progress) ac -
cording to the sequence of manoeuvres as en -
visaged in the programmed sequence.
Input configured as normally open.
When this command is sent, the control unit
activates the master (primary) leaf of the appli-
cation to complete an Opening manoeuvre.
Input configured as normally open.
When this command is sent, the control unit
activates the master (primary) leaf of the appli-
cation to complete a Closing manoeuvre.
Input configured as normally open.
When this command is sent, the control unit
activates the slave (secondary) leaf of the appli-
cation to complete the next manoeuvre follow-
ing the previous one (or still in progress)
according to the sequence of manoeuvres as
envisaged in the programmed sequence.
Input configured as normally open.
When this command is sent, the control unit
activates the slave (secondary) leaf of the appli-
cation to complete an Opening manoeuvre.
Input configured as normally open.
When this command is sent, the control unit
activates the slave (secondary) leaf of the appli-
cation to complete a Closing manoeuvre.
Input configured as normally open.
Robus 600-1000 – 9