RIB KING Manual Del Usuario página 6

4th PHASE (Adjustments and checks)
1 - Release the motors
2 - Adjust the mechanical stops by moving the leaf by hand into the completely open and closed position
3 - Check correct tightness of the stops
4 - Put the leaves into the intermediate position and then lock the motors. Move the leaves slightly by hand so the
gears engage.
5 - Put all the SW1 and SW2 microswitches on OFF and the dip 7-13 of SW1 on ON (in the case of an
electric lock also put dip switches 8-9-10 on ON)
6 - Put DIP 1 on ON. The DL1 LED flashes.
7 - Press the PROG button and hold it. The DL5 and DL3 LEDs on the side of the relays turn on. M1 must open
followed by M2 while PROG is pressed.
Low speed starts after 10 seconds.
Adjust it via the LOW SPEED trimmer.
Turn the TORQUE trimmer clockwise to increase force (if necessary).
8 - Release the PROG button. If necessary, reverse V with W of the motor(s) that close to re-establish
correct movement direction.
9 - Press the PROG button and hokd it. The DL4 and DL6 LEDs on the side of the relays turn on. M2 must close
followed by M1. Keep PROG pressed until the gate has closed completely.
10 - Put DIP1 on OFF. The DL1 LED stops flashing
5th PHASE (Programming total opening time)
1 - Both leaves are closed. Put DIP 2 on ON. The DL1 LED flashes.
2 - Press PROG. The first leaf opens, recording the times (M2 remains still in the closed position)
3 - When M1 has finished opening, wait 2 seconds and press PROG (M1 times are stored)
4 - The second leaf starts opening, recording the times.
5 - When M2 has finished opening, wait 2 seconds and press PROG (M2 times are stored)
6 - Wait for the length of time wanted before automatic closing and press the PROG button.
7 - M2 closes. When the offset between the two leaves is such that they will not override each other when closing, press PROG to close
M1.
8 - M1 closes with no risk of overriding M2. DL1 stops flashing.
9 - Both motors have stopped. Times are stored
10 - Put DIP2 on OFF.
6th PHASE (Programming pedestrian opening times)
1 - Both leaves are closed. Put DIP2 on ON. The DL1 LED flashes quickly.
2 - Put DIP1 on ON. The DL1 LED now flashes slowly.
3 - Make contact between the COM and Ped Butt terminals. The DL1 LED flashes.
4 - When the leaf is opened enough, again make contact between the COM and Ped Butt terminals. This
stops M1.
5 - Wait for the length of time wanted before automatic closing and then again make contact between
the COM and Ped Butt terminals.
6 - M1 closes. The times are stored.
7 - Put DIP 1 and DIP2 of SW1 on OFF.
7th Programming of the MOON, MOON CLONE, SUN remote controls, the BLOCK Wi-Fi key selector switch and the SPARK Wi-Fi
blinker
Check that the dual-colored DL7 LED on the MASTER Wi-Fi alternates red and green (empty memory)
1. Push and hold the PROG RX button on the MASTER Wi-Fi card for at least 3 seconds. Upon release, the dual-colored DL7 LED
flashes red for 10 seconds.
2. At this time, pushing one of the buttons on the remote control will memorize the code.
Note: The MASTER Wi-Fi, in addition to the code, also records the button/channel to be used. Therefore pay attention to which remote
control buttons are pushed during the code recording process because it is these which will later activate the entire opening
process.
If no code is given, after 10 seconds the red dual-colored DL7 LED of the MASTER Wi-Fi turns off indicating that the programming
procedure has been exited. The dual-colored DL7 LED flashes alternately red and green indicating that there is no code in the memory.
Correct code memorization is indicated by the dual-colored DL7 LED coming on green for 500 ms and a sound from the buzzer, indicating
ON
correct memorization.
1 2 3 4 5 6 7 8 9 After recording the last command, an additional 10 seconds is given for the next registration.
10 11 12 13 14 15 16
ON 3. Now, insert the BLOCK Wi-Fi key selector switch and turn it clockwise in order to memorize the BLOCK Wi-Fi key selector.
Correct code memorization is indicated by the dual-colored DL7 LED coming on green for 500 ms and a sound from the buzzer, indicating
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16
correct memorization. After recording the BLOCK Wi-Fi key selector, an additional 10 seconds is given for the next registration
4. Now, press the button S4 PROG TX on the SPARK Wi-Fi blinker card
Correct blinker code memorization is indicated by the dual-colored DL7 LED coming on green for 500 ms and a sound from the buzzer,
indicating correct memorization.
To complete the code registration process let 10 seconds pass until the red flashing DL7 LED turns off.
Alternately, pushing the PROG RX button on the side of the MASTER Wi-Fi card will cause the red flashing DL7 LED to turn off, indicating
completion of the memorization process.
8th PHASE Customising the configuration
The configuration can be modified by moving the various microswitches
Microswitches ON
DIP 3 Automatic closing activated
ON
DIP 4 Photocells active only in closing
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16
DIP 5 Pre-flashing for 3 seconds
DIP 6 K butt command and RADIO ineffective in opening
ON
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 DIP 7 Slowing down activated
DIP 8 Electric lock activated
DIP 9 Electric lock release stroke and easy release activated
DIP 10 Electric lock engage stroke activated
DIP 11 Black out function activated
(read the manual for more detail)
ON
1 2 3 4 5 6 7 8 9
DIP 12 Reclosing upon passage of the photocells activated
10 11 12 13 14 15 16
DIP 13 Sensitive edge monitoring SELFTEST activated
ON
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16
The DIP SWITCHES 14-15 and 16 must remain OFF for KING 230V
ON
JP 17 Closed for 2 motors. Open for 1 motor.
JP1, JP2 and JP3 must be closed.
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16
ON
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16
Microswitches OFF
Automatic closing deactivated
Photocells active all the time
Motor and flasher start together
K butt and RADIO step-by-step command
Slowing down not activated
Electric lock deactivated
Electric lock release stroke and easy release deactivated
Electric lock engage stroke deactivated
Black out function deactivated
Reclosing upon passage of the photocells
non activated
Sensitive edge monitoring SELFTEST deactivated
ON