General Information; After Operation; Routine Maintenance; Nuts And Bolts - Stiga BL 320E Manual De Instrucciones

For a grass catcher with contents indicator device:
Up = empty
Down = full
While working with the cutting means running, the
indicator remains raised for as long as the grass catcher
is able to hold cut grass; when it lowers, it means
that the grass catcher is full and must be emptied.
To remove and empty the grass catcher:
• Release the switch lever and wait for the
cutting means to stop (par. 6.5);
• Lift the rear discharge guard (Fig.8.A),
grasp the handle and remove the grass
catcher keeping it in an erect position.
STOP
6.5
To stop the machine:
1. Release the control lever (Fig.12.A).
2. Wait until the cutting means stops;
3. Disconnect the extension lead FIRST from the
general socket (Fig.12.B) and THEN from the
side of the lawnmower switch (Fig.12.C).
Always stop the machine:
• When moving between work areas.
• When driving on grass free surfaces.
• Every time it is necessary to overcome an obstacle.
• Before adjusting the cutting height.
• Whenever you remove or reattach the grass catcher.

AFTER OPERATION

6.6
1. Stop the machine (par. 6.5).
2. Allow the motor to cool before storing
in an enclosed space.
3. Clean (par. 7.2).
4. Check there are no loose or damaged components.
If necessary, replace the damaged components
and tighten any screws and loose bolts.
7.

ROUTINE MAINTENANCE

GENERAL INFORMATION

7.1
The safety regulations to follow are described in
chap. 2. Strictly comply with these instructions to avoid
serious risks or dangers.
Before conducting any inspections, cleaning or
maintenance/adjustment interventions on the machine:
• Stop the motor.
• Make sure that all moving parts have
come to a complete stop.
• Unplug the machine from the mains.
• Read the relevant instructions.
• Use suitable clothing, protective
gloves and goggles.
• The frequency and types of maintenance are
summarised in the "Maintenance Table". This
table will help you maintain your machine's
safety and performance. It summarises the main
interventions to be made and the frequency
applicable to each of them. Carry out the relevant
intervention according to the first deadline.
IMPORTANT Any maintenance and adjustment
operations not described in this manual must be carried
out by your dealer or Authorised Service Centre.
7.2 CLEANING
Clean thoroughly following the instructions
below every time it is used.
Cleaning the machine
7.2.1
• Do not spray water onto the motor and electrical
components and prevent them from getting wet (Fig.13).
• Do not use aggressive liquids to clean the chassis.
• To reduce fire hazards, keep the machine
and, in particular, the motor free of grass,
leaves, or excessive grease.
Cleaning the grass-catcher
7.2.2
1. Empty the grass catcher;
2. Shake it to remove grass cuttings and soil residue;
3. Wash and rinse it, then place it
where it can dry quickly.
Cleaning the cutting-means assembly
7.2.3
Remove grass debris and mud accumulated in the
cutting means assembly to prevent it from drying and
causing problems the next time the machine is used.
Tilt the machine laterally and make sure that
it is stable before starting any work.

NUTS AND BOLTS

7.3
Keep all nuts, bolts and screws tight to be sure
the equipment is in safe working condition.
8.

OCCASIONAL MAINTENANCE

CUTTING MEANS

8.1
A badly sharpened cutting means pulls at the
grass and causes the lawn to turn yellow.
Do not touch the cutting means until the machine
is switched off and the cutting means is completely
stationary.
All work on the cutting means (disassembly, shar-
pening, balancing, repairing, reassembly and/or repla-
cing) are demanding jobs that require special skills as
well as special tools. For safety reasons, these jobs are
best carried out at a Specialised Centre.
EN - 7