Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Operation
CHeCK POINTS beFOre
OPeraTION
•
Before power is applied, please check the cables
carefully.
•
The camera ID of the controller must be identical to
that of the camera to be controlled. The camera ID
can be checked in the System Information of OSD
Menu.
•
If your controller supports multi-protocols, the protocol
must be changed to match to that of the camera.
•
If you changed camera protocol by changing DIP
switch, the change will be effective after you reboot
the camera.
•
Since the operation method can be different for
each controller available, refer to the manual for your
controller if camera can not be controlled properly.
PreSeT aND PaTTerN
FuNCTION Pre-CHeCK
•
Check how to operate Preset, Scan, Auto Pan and
Pattern function with controller or DVR in advance to
operate camera function using them. (refer to your
System keyboard Manual)
•
If controller or DVR has no pattern button or function,
use shortcut keys with preset numbers. For more
information, refer to "Reserved Preset" in this manual.
auTO CalIbraTION
•
If the camera is continuously subjected to very high
temperature (over 50°C or 122°F) environment for a
long time, it is possible for the camera to lose focus.
As a result, you will get blurry image. In this case, it is
recommended to turn on "AUTO CALIBRATION" by
running Preset 165.
•
If you execute AUTO CALIBRATION, camera will
calibrate its focus at every 6 hours. To turn off this
function, please, run Preset 166.
16 – 36x IP Smart Dome Camera
STarTING OSD MeNu
•
Function
Using the OSD menu, Preset, Pattern, Auto Pan,
Scan and Alarm Input function can be configured for
each application.
•
Enter Menu
<Go Preset> [95]
reSerVeD PreSeT
•
Description
Some Preset numbers are reserved to special
functions.
•
Function
<Go Preset> [95]
: Enters into OSD menu
<Go Preset> [131~134] : Runs Pattern Function 1~4
<Go Preset> [141~148] : Runs Auto Pan Function 1~8
<Go Preset> [151~158] : Runs Scan Function 1~8
<Go Preset> [161~164] : Sets Relay 1~4 Output to OFF
<Set Preset> [161~164] : Sets Relay 1~4 Output to ON
<Go Preset> [165]
: Auto Calibration ON.
<Go Preset> [166]
: Auto Calibration OFF.
<Go Preset> [167]
: Zoom Proportional Jog ON
<Set Preset>[167]
: Zoom Proportional Jog OFF
<Go Preset> [170]
: Sets Camera BLC Mode to OFF
<Go Preset> [171]
: Sets Camera BLC Mode to HIGH
<Go Preset> [174]
: Sets Camera Focus Mode to AUTO
<Go Preset> [175]
: Sets Camera Focus Mode to Manual
<Go Preset> [176]
: Sets Camera Focus Mode to SEMI-
<Go Preset> [177]
: Sets Day & Night Mode to AUTO1
<Go Preset> [178]
: Sets Day & Night Mode to NIGHT
<Go Preset> [179]
: Sets Day & Night Mode to DAY
<Go Preset> [190]
: Sets OSD Display Mode to AUTO
<Go Preset> [191]
: Sets OSD Display Mode to OFF
<Go Preset> [192]
: Setting OSD Display Mode to ON
<Go Preset> [193]
: Sets all Privacy Mask Display to OFF
<Go Preset> [194]
: Sets all Privacy Mask Display to ON
<Go Preset>[200]
: Digital Zoom ON
<Go Preset>[201]
: Digital Zoom OFF
AUTO
(Except Privacy Mask)
(Except Privacy Mask)
(Except Privacy Mask)
Publicidad
Capítulos
Tabla de contenido
