Network Setup - Samsung SNC-C7478 Manual Del Usuario

Network Setup

QuICK STarT OF NeTWOrK
CONNeCTION
Please follow the steps below to complete the initial
setup of the Network Function.
Please do not power on the IP Smart Dome until
instructed.
Temporarily disable any proxy servers configured in
Internet Explorer.
If connecting the IP Smart Dome directly to a modem,
power down and reset the modem. Leave the modem
powered down until configurations are finalized with
the IP Smart Dome and the IP Smart Dome has been
correctly connected to the modem.
1. You will need to access a PC/laptop and should
configure that PC in order to communicate with
the IP Smart Dome. Record the current TCP/IP
properties of that PC (IP address, subnet mask,
gateway, DNS, etc)
If your PC obtains its IP address automatically, then
there is no need to record any information.
2. Change the IP address of that host PC to
192.168.1.11 and subnet mask to 255.255.255.0
(leave all other entries blank)
3. Connect the IP Smart Dome to your PC's
Ethernet port via the crossover cable (it does not
matter what end is used for the PC)
4. Power on the IP Smart Dome using the power
adapter.
5. After 60 seconds of power, verify a flashing
ACTIVE indicator, and a flashing or solid LINK
indicator. After the corresponding indicator lights
are properly displayed, open Internet Explorer.
6. Type - http://192.168.1.200 (the default IP of the
IP Smart Dome) into your address bar.
7. Default ID and Password to access IP Smart
Dome(root:4321)
8. Familiarize yourself with the Viewer Interface
Screen.
9. Locate the TCP/IP configuration under Setup
Tools. Supply the same ID and Password to
enter Setup Tools (root:4321)
10. Under "Network Type" select STATIC. You will
only select Dynamic if you are connecting the IP
Smart Dome directly to your cable modem and
your Internet Service Provider is supplying you a
dynamic address.
If you have a network with other devices (such as PC/
laptop, etc.) or a router, you will NEVER select
Dynamic.
 – 36x IP Smart Dome Camera
11. Configure the IP Smart Dome's IP settings as you
would any other PC on your network, providing a
proper IP address, Subnet Mask, Gateway, and
DNS server.
If this is standalone unit with a direct connection to a
cable modem then input the addresses you have
received from your ISP. If you received no IP address
from your ISP, please select Dynamic and choose the
proper settings.
12. The IP Smart Dome utilizes five ports - a HTTP
Webserver Port for utilizing Internet Explorer,
a Device Port, a TCP Streaming Port, a UDP
Streaming Port, Upload Port. If this IP Smart
Dome will be directly attached to a cable modem
or has been assigned a static IP from your ISP,
then leave the default port settings. If you are
installing the IP Smart Dome on a network, you
must define a HTTP Webserver Port other than
80. The other ports can remain unchanged.
13. If the IP Smart Dome is connected to a network
which utilizes a router, you must have Port
Forwarding configured on your personal router
to forward all ports to the IP address you have
assigned the IP Smart Dome.
14. After configuring Port Forwarding on your router
(if necessary), you may then access your IP Smart
Dome on your local network by opening Internet
Explorer and specifying the IP address and HTTP
Webserver Port that you have assigned to the IP
Smart Dome.
Examples: http://192.168.1.200:8888 or
http://24.106.88.123
If you left your HTTP Webserver Port set to 80, then
you don't need to specify the port in the Address Bar
when accessing your IP Smart Dome.
15. Access your IP Smart Dome via the Internet
If you used a static IP address assigned by
your ISP
i) Open Internet Explorer.
ii) Type the IP of the IP Smart Dome.
iii) If you use a router, type the routers' static
IP and the HTTP Port number of the IP
Smart Dome.
If you have a dynamic address provided by
your ISP
i) Run Internet Explorer.
ii) Type DDNS URL or IP address of router.
Then, press ENTER key.